-
LABVIEW 存储
labview存储与保存、
EXCEl单元格数据更改与保存(Labview Storage and Preservation
EXCEl Cell Data Change and Preservation)
- 2019-05-29 10:11:07下载
- 积分：1
-
Analog-LED--
先将字符串转化为像素图，再将像素图还原成二维数组。将二位数组转化为布尔数组。然后用一个顺序结构，第一帧放入比较程序，即显示汉字并闪烁程序。第二帧循环移位程序。第三帧屏幕关闭程序。(First string into a pixel map, and then reduced to a two-dimensional array of pixel map. The two-digit group into a Boolean array. Then a sequential structure, comparing the first frame into the program, the program that displays characters and flashes. The second frame cyclic shift procedure. The third frame of the screen to close the program.)
- 2014-04-15 10:58:17下载
- 积分：1
-
tutor
The project manager in MPLAB v3.40 has been extended to support multiple files. Previously established
projects from MPLAB v3.31 and earlier will be converted automatically by MPLAB v3.40 when they are
opened. Converted projects cannot be re-opened from previous versions of MPLAB.
- 2011-06-20 03:45:50下载
- 积分：1
-
hanshuxinhaofashengqi
1．采用Labview设计一虚拟函数信号发生器， 通过数据采集卡输出波形信号，调节信号的相关参数，可观察示波器上波形的变化情况。
⑴ 以NI MyDAQ数据采集卡作为输出接口；
⑵ 数据采集卡输出多种信号，至少完成三种波形：正弦波、三角波、方波(可调占空比)的输出，同时前面板上显示各输出波形；
⑶ 频率、幅值、初相位、直流偏移量和方波的占空比（0～100 ）等参数可以通过前面板控件调节。
⑷ 前面板可显示输出波形。(1. Labview design using a virtual function signal generator, data acquisition card output waveform signal, adjust the relevant parameters of the signal can be observed on an oscilloscope waveform changes.
⑴ with NI MyDAQ data acquisition card as output interface
⑵ data acquisition card output a variety of signals, to complete at least three waveforms: sine wave output, triangle wave, square wave (adjustable duty cycle), while each of the output waveform is displayed on the front panel
⑶ frequency, amplitude, initial phase, the DC offset and duty cycle square wave (0 to 100 ) and other parameters via the front panel controls to adjust.
⑷ output waveform can be displayed on the front panel.)
- 2015-04-25 18:26:52下载
- 积分：1
-
LabVIEW
1）、设计一个程序控制8个外设小灯的点亮方式，要求两种方式A:每个小灯间隔时间T，依次亮，时间T可调，并循环。B：先1.3.5.7.9亮隔时间T，2.4.6.8.10亮，并循环，T可调。 2）、要求主面板与硬件的8个小灯同步。 3）、通过网络在另一台计算机上控制此程序的运行（利用LabVIEW的DateSocket技术）((Network control of virtual instruments 1), design a program to control eight peripheral lights lit the way, the requirements in two ways A: each light interval T, followed by bright, time T adjustable, and circulation. B: first 1.3.5.7.9 bright every time T, 2.4.6.8.10 light, and circulating T-adjustable. 2), requires eight small lights of the main panel and hardware synchronization. 3), through the network control of this program running on another computer (using the LabVIEW DateSocket technology)))
- 2020-11-03 10:49:52下载
- 积分：1
-
使用labview实现加速度计和陀螺仪数据融合和显示3d姿态
使用labview实现加速度计和陀螺仪数据融合和显示3d姿态(use labview)
- 2015-09-04 01:50:00下载
- 积分：1
-
labview
利用6251采集卡，通过Labview完成热水杯智能温度控制实验(6251 acquisition card use, by the completion of a hot cup of Labview intelligent temperature control experiment)
- 2020-09-21 12:17:51下载
- 积分：1
-
FFT
说明： Labview环境下实现带汉明窗的傅里叶变换(Labview environment to achieve with a Hamming window Fourier transform)
- 2010-03-19 21:44:32下载
- 积分：1
-
program
控制三台电机，并完成转矩给定的分配，记录转速(Control three motors and complete the assignment given torque, speed record)
- 2013-09-18 16:25:52下载
- 积分：1
-
UDP基本通讯模块练习
UDP基本通讯模块，可以清楚的了解labview的UDP通讯方法，而且有一定的表明(labview UDP send model is helpful for us to learn this software)
- 2020-06-19 03:20:01下载
- 积分：1
