-
KalMat
Kalmat is a Matlab Non_linear Kalman Filtering Toolbox. With this toolbox it is made possible to use object oriented approach for implimenting the toolbox. compared to other available similar toolboxes this is much easier and also very user friendly.
- 2010-01-20 19:40:54下载
- 积分：1
-
path_discovery
自己编写的利用matlab实现无线自组织网AODV仿真的算法源码。
为由50个节点构成的网络。在50m×50m大小的区域内，随机的产生50个节点。由用户指定源节点和目的节点，程序负责给出从源节点到目的节点的最小路径和此路径的跳数。各个节点之间设定为只要在自己直接通信范围内的其它节点，均一跳可达。(Write your own realization of the use of matlab simulation of wireless self-organizing network algorithms AODV source. The grounds of a network of 50 nodes. Size of 50m × 50m in area, randomly generated 50 nodes. By the user to specify the source node and destination node, the program responsible for the given node from the source node to the destination path and this path is the minimum number of hops. Set between each node to communicate directly as long as within the scope of their other nodes, all jump up.)
- 2021-04-15 16:08:55下载
- 积分：1
-
bessel
此程序主要功能是 1 画出标准零阶贝塞尔函数，
2 在估计多普勒时，接收信号的实部或者虚部的自相关函数接近于贝塞尔函数，所以画出了一条接近于贝塞尔函数的曲线图(The main function of this program is 1 shows the standard zero-order Bessel function,
2 estimate the Doppler, the autocorrelation function of the received signal or the imaginary portion of the real part close to the Bessel function, so to draw a graph of the Bessel function is close to)
- 2014-09-20 15:16:24下载
- 积分：1
-
F16_dynam
F16开环动力学模型，采用C语言编写的MATLAB S函数。输入为油门及3个舵面共四个控制量，以及系统低阶、高阶选择器。前缘襟翼模型内部自动调节。输出为12个状态量以及油门大小。采用欧拉角坐标系。(F16 open-loop dynamic model, using the C language MATLAB S function. Throttle input, and three of four rudder control volume, and system low, high selector. Automatically adjust the front flap inside the model. The amount of output for the 12 states and the accelerator size. Using Euler angle coordinate system.)
- 2011-09-30 11:02:24下载
- 积分：1
-
Taylor_Algorithm
泰勒级数展开算法是需要初始估计位置的递归算法，在每一次的递归中通过求解TDOA测量误差的局部最小二乘来改进估计的位置。 本程序基于MATLAB，对泰勒级数展开算法进行了仿真。初始位置的选取很重要，建议和其他简单的算法进行协同，对信号源位置进行定位。 希望对研究信号源定位的同志有所帮助。(Taylor series expansion algorithm is the need to estimate the location of the initial recursive algorithm, in every recursive TDOA measurement error by solving the partial least squares to improve the position estimate. The program is based on MATLAB, the Taylor series expansion algorithm for the simulation. The selection of the initial position is very important, the proposed algorithm and other simple coordination, to locate the signal source location. Want to locate the source of research help comrades.)
- 2020-12-13 14:39:15下载
- 积分：1
-
CEEMDAN_V00
Matlab code for empirical mode decomposition
- 2018-01-02 06:17:32下载
- 积分：1
-
flt_calc
filter calculations matlab files
- 2010-06-13 17:37:49下载
- 积分：1
-
job-shop
基于PSO的job-shop调度源代码，上面已经上传了一个基于flow-shop调度问题，可以讲二者对比看(PSO-based job-shop scheduling of the source code has been uploaded above based on the flow-shop scheduling problem, you can talk about comparing the two to see)
- 2009-07-03 09:38:01下载
- 积分：1
-
ELM
MATLAB版极限学习机，自带训练集与测试集，可运行。(MATLAB version of the ELM, with its own data set)
- 2017-08-15 09:26:15下载
- 积分：1
-
EX080700
说明： 切比雪夫-2型低通滤波器设计
基于matlab仿真编程的(-2 Chebyshev low-pass filter design based on Matlab simulation programming)
- 2006-03-30 14:58:53下载
- 积分：1
