-
stopwatch
数字秒表的VHDL代码。当设计文件加载到目标器件后，设计的数字秒表从00-00-00开始计秒。，直到按下停止按键（按键开关S2）。数码管停止计秒。按下开始按键（按键开关S1），数码管继续进行计秒。按下复位按键（核心板上复位键）秒表从00-00-00重新开始计秒。(The VHDL code for digital stopwatch. When the design document loaded into the target device, the designed digital stopwatch count the seconds from the 00-00-00. Until you press stop key (key switch S2). Nixie tube stop count seconds. Press the start button (key switch S1), the digital control continue to count seconds. Press the reset button (core panel reset button) to restart the stopwatch count seconds from the 00-00-00.)
- 2010-03-02 17:17:58下载
- 积分：1
-
LCD-Driver-(LabVIEW-2009)
Lab view using FPGA traing on lcd pannel
- 2012-03-23 23:50:54下载
- 积分：1
-
Endat2_1_freq
用verilog实现endat2_1驱动,并用signalTap捕捉信号。(Using verilog achieve endat2_1 drive and use signalTap capture signal.)
- 2021-04-26 15:08:45下载
- 积分：1
-
count4
这是一个基于Quartus2 开发环境的4输入加法器( 4adder basic on Quartus2)
- 2013-08-04 09:45:07下载
- 积分：1
-
uart2spi-master
说明： this code works with spi and uart interfaces.
- 2020-07-21 21:10:59下载
- 积分：1
-
Cordic_matlab
实现自然对数运算的cordic算法的matlab浮点仿真，以及针对FPGA硬件平台的定点仿真测试(Achieve natural logarithm of cordic algorithm matlab floating point emulation, and FPGA hardware platform for fixed-point simulation testing)
- 2013-11-01 15:10:09下载
- 积分：1
-
StepperMotorDrivepinassign
stepper motor vhdl pin assignments and code
- 2011-08-12 23:15:46下载
- 积分：1
-
数字频率计
设计一简易数字频率计，其基本要求是：
1)测量频率范围0～999999Hz；
2)最大读数999999HZ,闸门信号的采样时间为1s；.
3)被测信号可以是正弦波、三角波和方波；
4)显示方式为6位十进制数显示；
5）具有超过量程报警功能。
5)输入信号最大幅值可扩展。
6）测量误差小于+-0.1%。
7)完成全部设计后，可使用EWB进行仿真，检测试验设计电路的正确性。(The basic requirements of designing a simple digital frequency meter are:
1) The measuring frequency range is 0-999999 Hz.
2) The maximum reading is 999999HZ, and the sampling time of gate signal is 1 s.
3) The measured signal can be sine wave, triangle wave and square wave.
4) The display mode is 6-bit decimal number display.
5) It has alarm function beyond range.
5) The maximum amplitude of input signal can be expanded.
6) The measurement error is less than +0.1%.
7) After completing all the design, EWB can be used to simulate and test the correctness of the circuit.)
- 2019-06-20 12:47:51下载
- 积分：1
-
rams
说明： combinatorial modules
- 2019-04-13 19:41:21下载
- 积分：1
-
pingpong
用Verilog代码实现的乒乓操作，用Verilog代码实现的乒乓操作(Verilog pingpong)
- 2016-01-15 17:35:06下载
- 积分：1
