-
cluster-codes
there are some clustering codes of matlab.
- 2011-06-05 11:22:07下载
- 积分：1
-
-MPPT-function
带有MPPT功能的光伏阵列Matlab通用仿真模型(PV array with MPPT function Matlab generic simulation model)
- 2013-11-17 09:16:50下载
- 积分：1
-
水位的最优发电效益
本程序旨在计算在整个调节时段的初末水位已知的情况下（水位均为170米），从后往前计算出每个阶段的各个水位到最后阶段的最优发电效益，逐步向前递推找出最大年发电效益，从而找到最优化的路径放入到矩阵LJ中，本程序未考虑防洪限制。(The purpose of this procedure is to calculate the optimal power generation benefit for each stage from the rear to the final stage (the water level is 170m) in the case where the initial water level of the whole adjustment period is known (the water level is 170m), and the maximum annual power generation benefit can be found gradually forward. In order to find the optimized path into the matrix lj, the procedure does not take into account the flood control limitation.)
- 2020-06-22 04:00:01下载
- 积分：1
-
function6
Pass the Images Through Optics -- Use a Gaussian "Aperture Function"
This code segement can use a measured aperture function just as easily - simply replace the next five lines by "load measured_aperture" where measured_aperture is the measured function strored in ASCII and the data stored in the file measured_aperture.mat is a MATLAB .mat file that contains the matrix apfunction. (in MATLAB type "help load" for how to use load and look at the c and fortran code that shows how to read and write MATLAB .mat files).
(Note: When the Point Spread Function is Gaussian, then so is the Aperture function)
To simulate the effect of the tracker optics, each of the movie frames is now blurred using a 2-D FFT (Fast Fourier Transform). The first frame of the resulting image is shown in Figure 1.
- 2011-02-12 00:30:05下载
- 积分：1
-
Image-Manipulation-Program
用几种函数实现傅里叶变换，变换后可输出图形(With several functions for Fourier transform, transform graphics output)
- 2011-05-03 15:37:09下载
- 积分：1
-
arrow
ARROW(Start,Stop) draws a line with an arrow Start to Stop (points should be vectors of length 2 or 3, or matrices with 2 or 3 columns), and returns the graphics handle of the arrow(s).
- 2015-02-03 16:19:42下载
- 积分：1
-
six_arm
说明： 利用matlab机器人工具箱对串联机器人末端机械臂的可能工作点绘制，达到较为直观的图形。(Making use of the MATLAB robot toolbox to draw the possible working points of the end manipulator of the serial robot, the more intuitive graphics can be achieved.)
- 2019-09-18 19:53:44下载
- 积分：1
-
ber_OFDM_64s_1e4_withclipping_snr20_differCR_1_2_3
限幅方法降低OFDM系统误码率，不通限幅率的比较曲线(reducing the OFDM PAPR with different CR in Clipping methord)
- 2009-04-04 12:38:11下载
- 积分：1
-
adaptive-control
自己编写的自适应控制程序，包括代码和simulink仿真模型。(His writing the adaptive control program, including code and simulink model.
)
- 2012-05-05 14:03:05下载
- 积分：1
-
matlab_code3
matlab下可以直接使用的小程序 包括各种常用算法 对应书籍为《matlab宝典》(matlab can be directly used for small programs, including such popular books as the corresponding algorithm " matlab Collection" )
- 2013-09-27 15:30:31下载
- 积分：1
