登录
首页 » matlab » chap9

chap9

于 2009-04-29 发布 文件大小:23KB
0 181
下载积分: 1 下载次数: 27

代码说明:

  先进PIDmatlab仿真PID参数整定参数程序(PIDmatlab advanced simulation parameters of PID parameter tuning process)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • Haar
    Wavelet de Haar aplicado a imagenes
    2011-01-17 02:36:58下载
    积分:1
  • matlab
    各种波形的matlab生成 可以观察波形图(Matlab various waveforms generated waveform can be observed)
    2011-05-31 15:03:12下载
    积分:1
  • duiou
    对偶单纯形法matlab编程,有逐句的说明(simplex write)
    2012-05-15 16:01:16下载
    积分:1
  • Opt.-Tech.-in-Wireless-Commun
    无线通信中的优化技术,原书,通过对现有已运行的网络进行数据分析、现场测试数据采集、参数分析、硬件检查等手段,找出影响网络质量的原因,并且通过参数的修改、网络结构的调整、设备配置的调整和采取某些技术手段。(Optimization of wireless communications technology by Sergiy A. Vorobyov and Yonina C. Eldar, the original book, through the existing network has been in operation for data analysis, field test data acquisition, parameter analysis, hardware checks and other means to identify the factors affecting the quality of the network, and by modifying the parameters of the network structural adjustment, and the adjustment device configured to take certain technical means.)
    2015-04-07 18:02:49下载
    积分:1
  • BG_Wael
    Matlab code for bacterial foraging
    2010-11-07 20:29:59下载
    积分:1
  • Matlab.practical.program
    matlab.practical.program介绍了matlab的发展和一些基本知识(matlab.practical.program on the development of Matlab and some basic knowledge)
    2007-01-16 00:54:32下载
    积分:1
  • Grid_side1
    基于电网电压定向的三电平并网逆变器的研究(And the three-level inverter grid voltage oriented network based on)
    2015-12-11 16:49:24下载
    积分:1
  • delay_fd
    处理雷达脉冲回波信号,提取目标的距离和多普勒频移信息(Processing of radar pulse echo signal, extract the target distance and Doppler shift information)
    2016-12-27 20:53:15下载
    积分:1
  • Eacpower
    this source code is eacpower matlab
    2013-08-04 17:42:35下载
    积分:1
  • DCT-and-Image-Compression
    DCT and Image Compression In the JPEG image compression algorithm, the input image is divided into 8-by-8 or 16-by-16 blocks, and the two-dimensional DCT is computed for each block. The DCT coefficients are then quantized, coded, and transmitted. The JPEG receiver (or JPEG file reader) decodes the quantized DCT coefficients, computes the inverse two-dimensional DCT of each block, and then puts the blocks back together into a single image. For typical images, many of the DCT coefficients have values close to zero these coefficients can be discarded without seriously affecting the quality of the reconstructed image. The example code below computes the two-dimensional DCT of 8-by-8 blocks in the input image, discards (sets to zero) all but 10 of the 64 DCT coefficients in each block, and then reconstructs the image using the two-dimensional inverse DCT of each block. The transform matrix computation method is used.
    2014-01-28 16:55:07下载
    积分:1
  • 696518资源总数
  • 106242会员总数
  • 10今日下载