-
forKPMtools
卡尔曼滤波，能够进行目标位置的预测与识别(Filter of Kalman)
- 2011-01-28 18:57:02下载
- 积分：1
-
jun-V0.7
有井曲线作为输入可计算其地震波的衰减,针对EMD方法的不足,分析了该信号的时域、频域、倒谱，循环谱等。( There is a well attenuation curve as input to calculate its seismic waves, For lack of EMD, Analysis of the signal time domain, frequency domain, cepstrum, cyclic spectrum, etc.)
- 2017-04-25 21:40:00下载
- 积分：1
-
kalmanshixian
本程序实现了kalman滤波功能，并附带了仿真图片(This procedure implements the kalman filtering, and with the simulation images)
- 2010-12-30 16:36:41下载
- 积分：1
-
image_processing
code for image processing, opening closing of an image, converting files from RGB, algorithm for extracting the edge
- 2012-05-13 23:23:08下载
- 积分：1
-
lms
自适应滤波，LMS算法，matlab编写，线谱提取(Adaptive filtering, LMS algorithm, matlab prepared line spectrum extraction)
- 2013-07-16 14:47:03下载
- 积分：1
-
LMS_RLS
自适应波速形成，RLS、LMS噪声对消器，，以及性能比较(Adaptive beamforming, RLS, LMS noise, as well as performance comparison canceller)
- 2013-12-15 12:53:04下载
- 积分：1
-
2dheatconductionproblem
2d heat conduction problem in matlab
- 2010-06-04 20:12:19下载
- 积分：1
-
projefinal
there is a code for tsai wu failure teory.
- 2020-07-04 19:40:02下载
- 积分：1
-
activeContoursSnakesDemo
本演示实现了主动轮廓模型由Kass等人提出。
要运行它的图形用户界面
1。基于MATLAB型引导提示。
2。关于“到现有的图形用户界面，点击”
3。选择在与本文件相同的目录snk.fig文件
4。按一下上方的绿色箭头启动图形界面
一旦GUI已经启动，您可以通过使用蛇
1。点击“新形象”，并加载输入图像。提供的样品图像。
2。平滑参数设置“西格玛”或保留其默认值并点击“过滤器”。这将平滑图像。
3。只要你点击“过滤器”，头发会出现交叉，用他们和你左击鼠标，您可以选择在图像上的初始轮廓的位置。会出现一个红色圆圈到处您单击并在多数情况下，你应该单击对象周围的一切你想要的部分。最后一点，必须挑选使用右键单击，以阻止更多的积分为MATLAB的要求。
4。设置各种蛇参数（在能源方面的相对权重的蛇目标函数）或离开它们的默认值，然后按一下他们“迭代”按钮。蛇会出现和移动，因为它收敛到它的低能量状态。(This demo implements the Active Contour Models as proposed by Kass et al.
To run it with GUI
1. Type guide on the matlab prompt.
2. Click on "Go to Existing GUI"
3. Select the snk.fig file in the same directory as this file
4. Click the green arrow at the top to launch the GUI
Once the GUI has been launched, you can use snakes by
1. Click on "New Image" and load an input image. Samples image are provided.
2. Set the smoothing parameter "sigma" or leave it at its default value and click "Filter". This will smooth the image.
3. As soon as you click "Filter", cross hairs would appear and using them and left click of you mouse you can pick initial contour location on the image. A red circle would appear everywhere you click and in most cases you should click all the way around the object you want to segment. The last point must be picked using a right-click in order to stop matlab for asking for more points.
4. Set the various snake paramete)
- 2010-07-05 11:54:13下载
- 积分：1
-
lmsalgorithm
信道估计中的LMS算法matlab程序，希望对大家有所帮助(LMS channel estimation algorithm matlab program, we want to help)
- 2010-07-09 17:30:59下载
- 积分：1
