登录
首页 » matlab » svdexp2

svdexp2

于 2008-04-23 发布 文件大小:1KB
0 94
下载积分: 1 下载次数: 294

代码说明:

  SVD去噪,构造的矩阵方法为对数据进行均匀分段,并对去噪前后的信噪比,均方差进行了对比。(SVD denoising, construction of the matrix method for the data sub-uniformity, and signal to noise ratio before and after denoising are compared variance.)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • chaptertwo
    机器人控制系统的设计与Matlab仿真--第二章代码 机器人PID控制(Robot Control System Design and Matlab simulation- chapter code PID control robot)
    2009-01-09 22:24:43下载
    积分:1
  • 3Dpeizhun
    这是一个三维图像配准算法,程序调试通过,方便大家学习!(This is a three-dimensional image registration, program debugging through, facilitate learning!)
    2010-12-10 10:52:26下载
    积分:1
  • CMI_2014_11_17_encode_decode
    此程序为CMI编译码程序,详细的介绍了CMI调制原理及解调的原理及过程(This procedure for CMI encryption procedures, detailed introduction to the principles and process of modulation and demodulation principle CMI)
    2014-11-17 20:57:12下载
    积分:1
  • MATLAB-simulink-vehicle
    基于MATLAB的simulink汽车仿真模型,按功能结构分割,得到汽车的能源-动力学模型(MATLAB simulation model based on the simulink car, according to the functional structure segmentation, automotive energy- kinetic model)
    2015-03-03 20:51:27下载
    积分:1
  • CFICA_11
    语音信号盲分离的一个号用的程序给大家共享,希望对大家有用(Blind separation of speech signals with a number of procedures to share, we hope to be useful)
    2010-12-25 21:08:49下载
    积分:1
  • H
    说明:  通信信号处理中的HDB3 matalb 仿真一例(Communications signal processing simulation of one case of HDB3 matalb)
    2010-07-17 13:02:54下载
    积分:1
  • Reconstruct_on_of_oversampled_cosine_modulated_fil
    本文首先推导出过采样滤波器组精确重构的条件, 由于此时所需的约束条件数比临界采 样时少, 因而可以设计出频域衰减特性更好的滤波器组(This paper is derived through sampling filters of exact reconstruction of conditions, due to time constraints required for critical extraction ratio When a small sample, so you can design a better frequency filter attenuation characteristics)
    2010-05-12 21:21:11下载
    积分:1
  • GM(11)
    灰色模型GM(1,1)原始数列经过光滑优化(Gray model GM (1,1) with smooth Optimized original series)
    2009-03-15 14:01:25下载
    积分:1
  • Turbo_code_simulation
    1. 程序中Turbo译码采用了MAP,LOG-MAP,和MAX-LOG-MAP三种算法。 2. 以xxx开头的四个mat文件是四种给定的Turbo码在译码时用到的参数,保存下来的目的是 加快仿真的速度,如果你所仿真的Turbo码不是程序中列出的任意一种,你可以通过函数 trellis来生成自己的相关参数。 3. 程序支持1/2和1/3两种码率的Turbo码,其中1/2码率的Turbo码通过矩阵[1 0 0 1]打 孔得到。在译码时通过对打孔位置添0恢复成1/3码率的码字。 4. 程序中的信噪比表示Eb/N0,通过此参数求得N0,对发送信号进行加噪。(1 program in Turbo decoding using the MAP, the LOG-MAP, and three kinds of the MAX-LOG-MAP algorithm.)
    2021-04-13 19:08:56下载
    积分:1
  • tiaozhijietiao2DPSK
    关于DPSK的matlab程序,看对大家有没有用(DPSK matlab program to see that everyone did not use)
    2012-06-22 17:04:20下载
    积分:1
  • 696524资源总数
  • 103838会员总数
  • 43今日下载