登录
首页 » matlab » methods_of_approximation

methods_of_approximation

于 2010-11-16 发布 文件大小:2KB
0 222
下载积分: 1 下载次数: 2

代码说明:

  函数逼近的实现方法,matlab程序集的源代码,相当不错,希望对大家有帮助(Implementation of approximation of function)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • case57
    IEEE57节点电力系统标准参数和潮流数据(IEEE57 node power system standard parameters and trend data)
    2012-06-04 15:19:57下载
    积分:1
  • 基于simulink的预测控制仿真 mpC
    基于simulink的预测控制仿真,很有借鉴意义。(Simulink simulation-based predictive control, useful reference.)
    2020-10-20 09:37:24下载
    积分:1
  • get-start-Matlab-2013a
    matlab 2013a starter guide
    2013-10-10 14:46:09下载
    积分:1
  • 二分法
    说明:  计算方法,二分法,弦截法应用。对于区间[a,b]上连续不断且f(a)·f(b)
    2020-04-17 12:46:03下载
    积分:1
  • CRLB
    说明:  基于TOA定位算法的克劳美罗CRLB仿真程序(CRLB simulation program of TOA location algorithm)
    2020-05-10 18:46:37下载
    积分:1
  • Appendix_A
    用FDTD算法计算金属腔间的电场反射,并且实时动画展现。(This program demonstrates a one-dimensional FDTD simulation.)
    2013-11-26 21:08:31下载
    积分:1
  • high-order-modreco
    基于高阶累积量的调制识别matlab源码,该算法可以对常用的2ask,2psk,2fsk,4ask,4psk,4fsk信号进行识别,准确率高。(high-order cumulants modulation recognition 2ask,2psk,2fsk,4ask,4psk,4fsk)
    2020-07-04 04:40:01下载
    积分:1
  • Selective
    数据链路层滑动窗口协议的设计与实现源码 信道模型为8000bps 全双工卫星信道,信道传播时延270 毫秒,信道误码率为10-5,信道提供字节流传输服务,网络层分组长度在240~256字节范围。(Sliding window data link layer protocol design and implementation of source-channel model 8000bps full-duplex satellite channel, the channel propagation delay 270 ms, the channel bit error rate of 10-5, the channel provides a byte stream transfer service, network layer packet length in the range of 240 to 256 bytes.)
    2013-12-08 11:45:53下载
    积分:1
  • mmplay_1
    编程中有的版本可能没有该功能函数,直接拷贝到工具箱里即可使用(Programming without the function of some versions may, directly copy to use can be a tool box )
    2015-03-29 19:37:13下载
    积分:1
  • ZF_MMSE_LMS_SATO_CMA
    1.原始信号A,通过信道受噪声污染后的信号q,然后分别经过均衡器ZF(MMSE)得到信号U,可以画出U的分布图 2.分别应用LMS,SATO,CMA算法得到U。(其中包括最佳延迟、均方误差的计算)所有结果均以图像形式显示。(1. The original signal A, subject to noise pollution through the channel after the signal q, and then through the equalizer, respectively ZF (MMSE) receive the signal U, the distribution of U can draw Figure 2. Were applied LMS, SATO, CMA algorithm to be U. (Including the best delay, mean square error terms) all the results are displayed in graphic form.)
    2010-01-05 22:12:21下载
    积分:1
  • 696516资源总数
  • 106641会员总数
  • 4今日下载