登录
首页 » matlab » Digital_Convert

Digital_Convert

于 2010-11-23 发布 文件大小:2KB
0 193
下载积分: 1 下载次数: 35

代码说明:

  数字变频器仿真,能将信号的频率在一定范围内变频。(the stimulation of Digital Convert,which can change the frequence of signal )

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • Fuzzy_AHP_method_and_Grey_Related
    基于灰色关联系数的模糊层次分析法。两种方法的综合运用,MATLAB编写,方便实用。(Correlation coefficient based on the fuzzy gray level analysis. Comprehensive use of the two methods, MATLAB prepared, convenient and practical.)
    2021-02-06 21:19:56下载
    积分:1
  • 3
    说明:  基于MATLAB的任意时刻三相短路电流计算(MATLAB-based three-phase short-circuit current calculations at any time)
    2010-03-28 00:15:51下载
    积分:1
  • ghash-clmulni-intel_glue
    Accelerated GHASH implementation with Intel PCLMULQDQ-NI instructions. This file contains glue code.
    2014-08-30 11:10:14下载
    积分:1
  • PCA33
    PCA用于故障诊断与检测,很有用的一个程序,希望你喜欢(PCA for fault diagnosis and detection, a useful program, I hope you like)
    2020-07-01 04:00:02下载
    积分:1
  • msk-modulator
    matlab msk modulator + gaussian filtr and GMSK modulator
    2015-03-07 20:55:25下载
    积分:1
  • Numericalalgorithmused
    常用数值算法 包括c++,c,MATLAB,等等(Numerical algorithm used includes c++, c, MATLAB, etc.)
    2010-06-28 16:26:36下载
    积分:1
  • two-dimensional-gausian
    two dimensional gausian
    2011-11-24 13:10:31下载
    积分:1
  • Permanent-magnet-synchronous.
    Permanent magnet synchronous motor parameters, structure, performance design process.
    2013-12-10 05:34:27下载
    积分:1
  • GMSK_matlab
    利用matlab仿真GMSK的源程序 按照移动通信的原理编写的程序,很容易懂(simulation using Matlab GMSK according to the source mobile communications prepared by the principle procedures, it is easy to understand)
    2007-05-20 16:56:30下载
    积分:1
  • power_3phsignaldq
    A Discrete 3-Phase ProgrammableSource block is used to generate a 1 pu, 15 degrees positive sequence voltage. At t = 0.05 s the positive sequence voltage is increased to 1.5 pu. At t = 0.1 s an unbalance is introduced by adding a 0.3 pu negative sequence component with a phase of -30 degrees. The magnitude and phase of the positive-sequence component is evaluated in two diiferent ways: 1) Sequence calculation of phasors using Fourier analysis and 2) abc to dq0 transformation. Math Function and Trigonometric Function blocks are used to evaluate the magnitude and phase of the positive sequence from the d and q components: V1 = sqrt(Vd^2 + Vq^2) , Phi1 = atan(Vq/Vd))
    2011-10-19 22:18:57下载
    积分:1
  • 696516资源总数
  • 106409会员总数
  • 8今日下载