-
max_min_curve
说明： 曲线最大最小值标记的MATLAB程序。需要的来下载。(Minimum curve marking the largest program of MATLAB. Need to download.)
- 2009-08-02 17:56:59下载
- 积分：1
-
Bondad
Program to calcule the Bondad
- 2012-05-24 19:58:30下载
- 积分：1
-
vb
说明： 材料力学中不同梁（简支梁、悬臂梁）受力分析计算程序(Mechanics of materials with different beam (Charpy, Izod) stress analysis calculation program)
- 2014-10-23 15:57:17下载
- 积分：1
-
appliedilitigatiobase
Large condenser iS one of the key heater exchange equipmems in heat—engine
plant and petrochemical industry．For the unclear cooling water and chemical reactions
during heat exchange when the condenser is running，the fouling which is not
favorable for heat transfer is accumulated in the inner wall of condenser tube．These
fouling have produced such harm：severely decreases the heat exchange capacity of
the condenser,lowers the vacuum degree，increases energy consumption and probably
leads to accidence due to the blockage of condenser tube and followed by erosion and
perforation
- 2015-11-17 22:46:07下载
- 积分：1
-
Three-spline-interpolation-procedure
数值分析，多项式插值，三次样条插值程序，自然边界条件。(Three spline interpolation procedure.)
- 2015-12-29 10:27:19下载
- 积分：1
-
buckPWM
Buck PWM controls the firing signal of Buck cnverter.
- 2012-05-11 20:30:34下载
- 积分：1
-
insertion_sort
Program to carry out insertion sort in C
- 2014-10-05 05:53:26下载
- 积分：1
-
dijkestra
Dijkestra Algorith coded in matlab
- 2011-12-17 17:49:13下载
- 积分：1
-
bottom_up_segmentation
这是TD算法的逆过程，首先将时间序列，划分为相邻点的短序列，当然此时的拟合误差为0，因为第一点和第二点的连线，原始点都落在线段上。将相邻两个线段连接起来，此时每条线段包含三个原始点，计算中间那个点的拟合误差。这样，所有这些三个点的线段中的中间点的拟合误差计算出来后，找出误差最小且误差小于阀值R的分段，作为第一条包含三个点的线段。 在上面的基础上，第一条分段同样的和相邻线段连接，然后计算每一条分段的拟合误差，再找出误差最小且小于阀值R的分段，作为第二个分段。依次方式循环，直到所有分段的拟合误差都小于阀值R，分段结束。
(This is the reverse process of TD algorithm, the first time series is divided into short sequences adjacent dots, of course fitting error is zero at this time, because the first and second points of connection, the original point fall line on. The two adjacent segments are connected, then each segment contains three original point, the intermediate fitting error calculated that point. Thus, after all these segments fitting error of three points in the intermediate point calculated to find the minimum error and the error is less than the threshold R segment, as the first line contains three points. Based on the above, the first segment and the adjacent line segment connecting the same, and then calculate a fitting error for each segment, and then find the smallest error and less than the threshold R segment, as the second segment . Followed by a cyclic manner until all segments fitting error is less than the threshold R, segment ends.)
- 2021-03-20 16:29:18下载
- 积分：1
-
lcmvzhankuan
基于SMI算法的零陷展宽算法，能够有效展宽信号方向图的零陷位置(Based on the SMI algorithm, the zero broadening algorithm can effectively widen the zero position of the signal pattern)
- 2017-03-19 16:27:43下载
- 积分：1
