登录
首页 » Visual C++ » Matlab

Matlab

于 2009-12-13 发布 文件大小:239KB
0 319
下载积分: 1 下载次数: 3

代码说明:

  文档介绍了matlab工具箱的使用情况。对于初学者是非常有帮助的。(Document describes the use of matlab toolbox. For beginners it is very helpful.)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 4.3
    主要用途是对抗多径衰落。由于多径衰落的存在,使得同一个帧由于路径不同,到达用户端的时延有先有后。在相关的频域上的会造成子载波之间的相互干扰,影响 性能。另外,由于有了循环前缀,使得IFFT FFT操作把原来的线性卷积变成循环卷积,大大简化了相应的信号处理复杂度(The main purpose is to fight against multipath fading. Due to the presence of multipath fading, the first after they have the same frame different paths to reach the client delay. Would cause mutual interference between sub-carriers in the frequency domain, affecting performance. In addition, thanks to the cyclic prefix, so IFFT FFT operation to the linear convolution of the original into a circular convolution, greatly simplifying the corresponding signal processing complexity)
    2012-08-24 15:17:41下载
    积分:1
  • ssa
    ssa,用于在matlab中的noise analysis(ssa, used in matlab noise analysis)
    2013-08-06 16:39:36下载
    积分:1
  • PQ
    说明:  应用于并网的分布式发电或微网系统 PQ控制要求电站的有功和无功是可控的(The distributed power generation or microgrid system PQ control applied to the grid requires that the active and reactive power of the plant is controllable)
    2017-09-20 19:18:08下载
    积分:1
  • matlog
    VRP, for solving vehicle routing problem
    2012-06-29 21:27:26下载
    积分:1
  • Recursive_integer_division
    递归法求解整数划分。 整数划分,是指把一个正整数n写成如下形式: n=m1+m2+…+mi (其中mi为正整数,并且1 <= mi <= n),则{m1,m2,...,mi}为n的一个划分。 如果{m1,m2,...,mi}中的最大值不超过m,即max(m1,m2,...,mi)<=m,则称它属于n的一个m划分。这里我们记n的m划分的个数为f(n,m) (Recursive method integer division. Integer division, refers to a positive integer n written as follows: n = m1+m2+ ...+mi (where mi is a positive integer, and 1 < = mi < = n), then {m1, m2, ..., mi} is a division of n. If {m1, m2, ..., mi} does not exceed the maximum value of m, i.e., max (m1, m2, ..., mi) < = m, m n is said that it belongs to a division. Where m is the number of division n our mind is f (n, m) )
    2014-02-06 14:21:38下载
    积分:1
  • MatlabEngine_link
    VC调用matlab的典型编程,采用matlab引擎的方法,成功实现了Vc对matlab的调用。并且做了可视化的界面。把程序中的main_edgelink2换成自己要调用的matlab程序(VC typical call Matlab programming using Matlab engine, the successful implementation of the Vc Matlab call. Done a visual interface. The procedures main_edgelink2 replaced by themselves to the calling procedure Matlab)
    2007-06-08 22:14:15下载
    积分:1
  • mtpa
    说明:  采用mtpa矢量控制方法对永磁同步电机进行转速控制,调速范围宽(pmsm mtpa controller)
    2019-08-19 19:39:33下载
    积分:1
  • duilie
    循环双端队列的元素插入,删除,以及输入输出(Double-ended queue, circular element insertion, deletion, and the input-output)
    2010-01-11 12:39:06下载
    积分:1
  • Signal-Repeater
    signal for PC software
    2014-10-18 13:31:53下载
    积分:1
  • matlab
    matlab exercise hope can be useful
    2012-08-06 20:45:46下载
    积分:1
  • 696516资源总数
  • 106658会员总数
  • 16今日下载