登录
首页 » matlab » New_matlab2

New_matlab2

于 2009-12-15 发布 文件大小:2KB
0 191
下载积分: 1 下载次数: 4

代码说明:

  MATLAB初学者 MATLAB初学者 包好了一些用matlab做无约束规划的源程序(MATLAB beginner beginner package MATLAB with matlab to do some good non-constrained programming source code)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • LBMpoiseuille
    Example codes for latiiic boltzmann
    2011-09-29 18:12:40下载
    积分:1
  • GeneticProgram
    说明:  遗传算法及说明 遗传算法及说明。(Genetic algorithm and describe genetic algorithms and description.)
    2008-10-28 10:43:15下载
    积分:1
  • SOM_NN_CODE
    An important aspect of an ANN model is whether it needs guidance in learning or not. Based on the way they learn, all artificial neural networks can be divided into two learning categories - supervised and unsupervised. • In supervised learning, a desired output result for each input vector is required when the network is trained. An ANN of the supervised learning type, such as the multi-layer perceptron, uses the target result to guide the formation of the neural parameters. It is thus possible to make the neural network learn the behavior of the process under study. • In unsupervised learning, the training of the network is entirely data-driven and no target results for the input data vectors are provided. An ANN of the unsupervised learning type, such as the self-organizing map, can be used for clustering the input data and find features inherent to the problem.
    2015-04-15 00:03:32下载
    积分:1
  • morph
    实现图像morphing的matlab代码(Image morphing realize the matlab code)
    2008-03-05 10:17:03下载
    积分:1
  • spectral_clustering
    谱图法的Matlab实现,复杂网络社区挖掘算法很常用的算法(Spectrum chart Matlab, the complex network community mining algorithm is very common algorithm )
    2012-05-09 21:18:48下载
    积分:1
  • Link-a-System-Level-OFDM-Simulator
    针对OFDM系统,分成链路级仿真和系统级仿真两个部分。为了降低系统级仿真的复杂度,采用链路级仿真的部分结果。(It contains mainly two parts, i.e. link-level simulator and system-level simulator. Link-level simulator focus on a single-cell single-user scenario, where signal is transmitted from tx, and estimated at rx. Comparing the difference in tx/rx signal, the error rate can be found out. The output of the link-level simulator is the BLER/BER vs. SNR mapping table, that can be used for the system-level simulation. System-level simulator focus on a multi-cell multi-user scenario. For the sake of simplicity, it takes the mapping table aquired in the link-level simulation, measure the actural SNR, and finds the corresponding error rate. Link-level simulator support SISO, 1 by x MRC, 2 by 1 STBC/SFBC, 2 by 2 Alamouti, x by 1 Antenna selection, x by y antenna selection. System-level simulator, currently support only SISO and 1 by 2 MRC. To start with, go into the folder sys_link_simu, and excute the following commond from matlab: sys_link_simu_func(a,b) where a is the link ada)
    2011-08-09 11:00:53下载
    积分:1
  • z_bus_new
    z bus formation code using modification
    2017-11-01 14:34:57下载
    积分:1
  • erfenfaheNewtonXiashan
    说明:  包括二分法,Newton下山法和improved Newton迭代法(Including the dichotomy, Newton downhill method and improved Newton iteration method)
    2008-10-25 18:56:34下载
    积分:1
  • Leachjihe
    所有关于Leach协议Matlab仿真都可运行,(Matlab simulation of all on the Leach agreement can be run)
    2011-05-19 17:22:04下载
    积分:1
  • VQC1
    VQC控制原理讲义,详细讲了VQC无功控制的原理(VQC )
    2014-08-16 18:18:20下载
    积分:1
  • 696516资源总数
  • 106554会员总数
  • 12今日下载