-
turbo
Turbo码编码仿真程序，在Matlab环境下仿真，适用于初学者。(Turbo coding simulation program, in the Matlab simulation environment for beginners.)
- 2009-01-06 20:38:54下载
- 积分：1
-
Data-processing
基于FFT的功率谱分析程序设计与应用
2）对实验所采集的转子振动信号进行频谱分析
2．讨论：
1) 信号经过均值化处理或不经过均值化处理的结果比较
2）采用不同窗函数时的谱结果（矩形窗函数, 汉宁窗函数，汉明窗）
3）典型函数的频谱（矩形窗函数, 汉宁窗函数，直线，阶跃函数，δ函数，方波，三角波等）
4）整周期和非整周期采样时两者的比较
5）讨论实验结果
(Based on the FFT power spectrum analysis of program design and Application2) on experimental collection of the rotor vibration signal spectrum analysis2 discussion:1) the signal through the mean treatment or not after a mean treatment results comparison2) using different window function spectral results ( rectangle window, Hanning window function, the Hamming window )3) the typical functions of spectrum ( rectangle window, Hanning window function, linear, step function, function, square wave, triangular wave)4) the whole cycle and non-integer-period sampling time comparison5) discussion of experimental results)
- 2012-01-05 15:45:44下载
- 积分：1
-
QR
说明： 该程序是基于QR分解的V-BLAST检测算法,两种算法，包括QR分解算法和SQRD算法。(The program is based on QR decomposition V-BLAST detection algorithm, two algorithms, including QR decomposition algorithm and SQRD algorithm.)
- 2017-03-13 20:38:23下载
- 积分：1
-
SER_DF_Coop
说明： DF协作系统MPSK SER分析,包括SER上界,高信噪比条件下的优化功率分配的SER仿真结果.(DF analysis of MPSK SER Collaborative System, including the SER upper bound, under the conditions of high signal to noise ratio to optimize power distribution simulation results of SER.)
- 2009-07-30 16:45:01下载
- 积分：1
-
lingoeazyjiaocheng
lingo入门教程，附有很多基础命令以及简单问题的分析，求解。例如病人吃饭，场地选址，渡河问题，人员相容问题，顺序安排工作问题，最短路线等等。(lingo Getting Started tutorial, with a lot of basic commands and a simple analysis of the problem, solution. For example, patients eat, site selection, cross the river issues, staff compatibility issues, the issue of work order of the shortest route and so on.)
- 2010-05-13 13:02:23下载
- 积分：1
-
gscale
GSCALE Scales the intensity of the input image.
G = GSCALE(F, full8 ) scales the intensities of F to the full
8-bit intensity range [0, 255]. This is the default if there is
only one input argument.
G = GSCALE(F, full16 ) scales the intensities of F to the full
16-bit intensity range [0, 65535].
G = GSCALE(F, minmax , LOW, HIGH) scales the intensities of F to
the range [LOW, HIGH]. These values must be provided, and they
must be in the range [0, 1], independently of the class of the
input. GSCALE performs any necessary scaling. If the input is of
class double, and its values are not in the range [0, 1], then
GSCALE scales it to this range before processing.
The class of the output is the same as the class of the input.
Copyright 2002-2004 R. C. Gonzalez, R. E. Woods, & S. L. Eddins
Digital Image Processing Using MATLAB, Prentice-Hall, 2004
$Revision: 1.5 $ $Date: 2003/11/21 14:36:09 $
- 2014-10-07 09:10:58下载
- 积分：1
-
CrossOver
CrossOver code in matlab
- 2015-04-05 00:17:25下载
- 积分：1
-
colorseg
此函数主要用欧式距离法和maha法实现图像分割。简单实用。(Image segmentation)
- 2013-05-21 21:56:48下载
- 积分：1
-
Modulations1
This file includes FSK,OOSK and QPSK modulations.
- 2009-02-25 23:14:54下载
- 积分：1
-
QAM_timing
说明： 硕士论文，介绍关于QAM系统中定时同步的方案。(Master s thesis about the Timing on QAM systems)
- 2011-02-17 22:45:01下载
- 积分：1
