登录
首页 » matlab » ria_organic_matter_fluorecence

ria_organic_matter_fluorecence

于 2010-06-11 发布 文件大小:6593KB
0 197
下载积分: 1 下载次数: 8

代码说明:

  The combination of EEM fluorescence and parallel factor analysis has proved to be a promising tool for studying DOM. These relatively inexpensive fluorescence measurements can be used in combination with other measurements to rapidly quantify and characterize DOM across a range of environments. This approach also has great potential in a wide range of other applications such as drinking water monitoring, waste water treatment control and the evaluation of ballast water exchange in ships. However, as with many new techniques, it is not as straightforward as could be desired and there are a range of potential pitfalls. For the approach to persist and become a trustworthy method, a basis for a standardized approach was required.

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • tcoding_zip
    turbo coding few files part 2
    2012-05-17 16:26:45下载
    积分:1
  • speech_course_2004
    This is my first upload which contain some stuff files from my final project.
    2013-03-21 16:45:09下载
    积分:1
  • dmc
    DMC控制 当系统的参数知道很少时可以利用这种方法进行运算 从而很好的控制(DMC control parameters when the system knows very little use of this method can well control operations to)
    2011-09-19 16:54:14下载
    积分:1
  • Notch_Filter
    an implementation of Notch_Filter in matlab for image processing
    2009-03-20 14:41:34下载
    积分:1
  • OFDMcode42
    This code was used for making the practical measurements in section 2.3 of my thesis. This Matlab code allows an OFDM signal to be generated based on an input data file. The data can be random data, a grey scale image, a wave file, or any type of file. The generated OFDM signal is stored as a windows wave file, allowing it to be viewed, listened to and manipulated in other programs. The modified wave file can then be decoded by the receiver software to extract the original data. This code was developed for the experiments that I performed in my honours thesis, and thus has not been fully debugged. This is the original code developed for the thesis and so has several problems with it. The BER performance given by the simulations is infact Symbol Error Rate. (This code was used for making the practical measurements in section 2.3 of my thesis. This M atlab code allows an OFDM signal to be generated based on an input data file. The data can be rando m data, a gray scale image, a wave file, or any type of file. The OFDM signal is generated stored as a windows wave file, allowing it to be viewed. listened to and manipulated in other programs. The modified wave file can then be decoded by the receiver software to extract the original data . This code was developed for the experiments th at I performed in my honors thesis, and thus has not been fully debugged. This is the original code developed for the thesis and so ha 's several problems with it. The BER performance given by the simulations is infact Symbol Error Rate.)
    2007-04-04 22:20:23下载
    积分:1
  • MUSIC
    运用MUSIC 算法仿真均匀圆阵的测向。经典算法(MUSIC algorithm simulation using uniform circular array to the test. Classical algorithm)
    2009-05-12 11:20:41下载
    积分:1
  • kalmantrackingcode
    基于kalman滤波的目标跟踪代码,用matlab实现了对目标的跟踪。(Kalman filter based target tracking code, matlab achieve the target tracking.)
    2021-02-05 10:19:57下载
    积分:1
  • Dvr-linear-harmonics
    This paper describes the problem of voltage sags and swells and its severe impact on non linear loads or sensitive loads. The dynamic voltage restorer (DVR) has become popular as a cost effective solution for the protection of sensitive loads voltage sags and swells. The control of the compensation voltages in DVR based on dqo algorithm is discussed. It first analyzes the power circuit of a DVR system in order to come up with appropriate control limitations and control targets for the compensation voltage control. The proposed control scheme is simple to design. Simulation results carried out by Matlab/Simulink verify the performance of the proposed method.
    2014-10-09 01:24:00下载
    积分:1
  • PCM-coding-MATLAB-implementation
    PCM编码MATLAB实现,能够在MATLAB环境下实现PCM量化编码,编码效率高,编码易于实现,简单易懂(PCM coding MATLAB, the MATLAB environment to achieve PCM quantization coding, coding efficiency, coding is easy to implement, easy to understand)
    2013-10-08 16:02:26下载
    积分:1
  • pca
    使用MATLAB开发环境,来 实现人脸识别(fase recognition)
    2009-03-20 10:30:55下载
    积分:1
  • 696516资源总数
  • 106562会员总数
  • 4今日下载