-
CP0802
uwb无线电基础代码，第九章，超宽带信道与接收机，共四个程序。(based on UWB radio code, Chapter IX, ultra-wideband channel with the receiver, a total of four procedures.)
- 2007-10-18 15:24:25下载
- 积分：1
-
Matlab_and_Modelsim_Codebug
matlab与modelsim的联调教程，pdf格式的(matlab FBI and the modelsim tutorial, pdf format)
- 2009-05-24 15:44:47下载
- 积分：1
-
modeling
说明： 为建立供热管网的在线优化运圩、故障实时诊薪
及赏真分析和培训呆缆，必须建立一种高精度的蒸巍供热管
习动恋仿真模型。该模型将蒸汽处理成为单相可压缩洗件，
将营罔处理成为由节点南支路组成的一种网络结构。在仿真
计算中，采用隐式Euler算法、线性迭代方法和稀疏矩畦算
法隶解由物理模型所得的非线性擞分方程组。证明7|：角的
算法具有大范围收敛特性。此方法祷被应 于青岛百蒸汽供
热管网的工程项目中。(Steam heating network of dynamic simulation modeling)
- 2011-03-07 16:36:48下载
- 积分：1
-
PSK_SER_Curves
plot the psk curves .Useful for the beginners.
- 2013-03-14 18:04:38下载
- 积分：1
-
SPWM
正弦波脉宽调制程序，适合初学者入门，可以直接运行(Sine pulse width modulation procedures, suitable for beginners entry, you can directly run)
- 2015-03-26 13:44:05下载
- 积分：1
-
DUOJING
本人收集的关于多径衰落、瑞利，RICE信道、QPSK等仿真程序，经过本人测试，全部可用，并附上测试结果及仿真图.(I collected on the multipath fading, Rayleigh, RICE channel, QPSK simulation program, etc., after I test, all available, along with test results and simulation of Fig.)
- 2009-06-05 14:41:58下载
- 积分：1
-
choicephase
故障突变量计算
12point滤序,需改为根据N自动确定滤序公式
设置故障突变量单相定值
设置故障突变量相间定值
设置故障突变量负序零序电流定值( Fault calculation 12point mutations order filter is required to determine the filter order based on the formula N automatically set the amount of single-phase fault mutation set fault value value mutation set the amount of white mutant the amount of negative sequence fault zero sequence current value)
- 2011-01-26 19:50:57下载
- 积分：1
-
sim
调制指数为0.5的2幅度CPFSK信号的相位轨迹图仿真模型。simulink模型(Modulation index range of 0.5 to 2 CPFSK signal simulation model of the phase trajectories. simulink model)
- 2011-06-06 08:33:02下载
- 积分：1
-
csmch
functioning invovled in addintion and removal of noise
- 2011-08-06 20:29:51下载
- 积分：1
-
Test
Speech Recognition System
- 2011-09-01 05:53:28下载
- 积分：1
