登录
首页 » matlab » wave_bases

wave_bases

于 2010-12-14 发布 文件大小:1KB
0 153
下载积分: 1 下载次数: 2

代码说明:

  wavelet,很好用的原码哦,一起试试吧(wavelet, with the original code Oh well, try it with)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • pablo
    国外使用面元法计算翼型升力的matlab程序包(matlab program using panel method to solve the lift of the foil)
    2021-03-02 11:59:33下载
    积分:1
  • cjtj
    基于matlab的成绩统计表,输入成绩,自行统计最高分,最低分,均分等(Matlab-based performance statistics, enter grades, self Statistics highest score, lowest score, sharing, etc.)
    2013-07-26 16:44:34下载
    积分:1
  • inverse work example
    文件里面是关于地震反演的文档和MATLAB程序实例,适合反演初学者使用学习。(Document which is a document and MATLAB instance on seismic inversion, for beginners to learn the inversion.)
    2020-11-07 16:49:49下载
    积分:1
  • PVI100K3TL
    说明:  实现100KW光伏并网逆变,双闭环PI解耦控制,锁相跟踪,功率计算等(Control method for three phase grid-connected inverter)
    2019-09-29 15:54:54下载
    积分:1
  • Cyclic-codes-and-decode-GUI
    循环编码,校验子译码,梅吉特译码,GUI界面设计。程序完整,可以良好运行,注释清晰。(Cyclic codes, check subdecode, Meggitt decoder, GUI interface design. Integrity of the process, you can run a good, clear notes)
    2013-10-02 22:38:23下载
    积分:1
  • 项目4
    说明:  任务:设计一个4×2.5Gbit/s 长距离光纤传输系统,并利用OptiSystem 仿真验证。 要求: 1.采用波分复用技术,波长设置以100GHz 为间隔,频率分别为193.1THz、193.2THz、193.3THz、193.4THz,每个波长传输速率为2.5Gbit/s(NRZ),传输距离为300km。采用常规光纤,光纤损耗系数为0.25dB/km。 2.单通道光发送机最大输出功率为0dBm,光接收机的接收光功率不低于-26dBm,过载点为-10dBm。 3.可以采用EDFA 作为线路放大器,其中EDFA 的输入功率限制在-18~2dBm,最大输出功率20dBm,增益范围为13~25dB,噪声指数4.0dB。(Task: Design a 4 x 2.5 Gbit/s long-distance optical fiber transmission system, and use OptiSystem simulation to verify. Requirement: 1. Using wavelength division multiplexing technology, the wavelength is set at 100GHz intervals, with frequencies of 193.1 THz, 193.2 THz, 193.3 THz and 193.4 THz, respectively. The transmission rate of each wavelength is 2.5 Gbit/s (NRZ), and the transmission distance is 300 km. The loss coefficient of conventional optical fibers is 0.25dB/km. 2. The maximum output power of a single-channel optical transmitter is 0 dBm, and the receiving power of an optical receiver is not less than -26 dBm, and the overload point is -10 dBm. 3. EDFA can be used as line amplifier, where the input power of EDFA is limited to - 18-2dBm, the maximum output power is 20dBm, the gain range is 13-25dB, and the noise index is 4.0dB.)
    2019-05-13 09:39:41下载
    积分:1
  • mt
    说明:  电机矢量控制,将电机转子,定子定位在MT轴,simulink仿真(motor simulink)
    2009-05-10 10:00:43下载
    积分:1
  • gabor(matlab)(C)
    可以实现Gabor变换,其中包含了采用C语言和Matlab两种工具实现(can achieve Gabor transform, which contains the C language and tools to achieve both Matlab)
    2007-03-15 13:41:31下载
    积分:1
  • fcss1
    模糊C-球壳(FCSS)聚类算法在matlab中的实现(Fuzzy C-spherical shells (FCSS) clustering algorithm to achieve in the matlab)
    2009-05-17 09:11:52下载
    积分:1
  • WinRAR-
    雅克比迭代解非齐次线性方程组,逐次求出近似解逼近精确解(Jacobi iterative solution of non-homogeneous linear equations, the successive approximation of the exact solution obtained approximate solution)
    2011-11-25 09:08:25下载
    积分:1
  • 696518资源总数
  • 105877会员总数
  • 14今日下载