-
基于LabVIEW的通用自动测试系统设计
基于LabvIEw的通用自动测试系统(ATs)舍计算机，可鳊程激励、响应数据采集及uuT模块，采用MxI总线控制方式。专用信号发生器为uuT提供模拟激励信号，矩阵开关和适配器完成不同信号间切换。主控计算机执行测试程序，信号发生器发送激励信号，数据采集卡采集数据，采集数据经调理后，并与标准数据|匕较是否满足相应测试结果。(The general automatic test system (ATs) based on LabvIEw can be used as a computer to excite, respond to data acquisition and uuT module. The control mode of MxI bus is adopted. Special signal generator provides analog excitation signal for uuT, matrix switch and adapter complete switching between different signals. The main control computer executes the test program, the signal generator sends the excitation signal, the data acquisition card collects the data, after the data acquisition is adjusted, and compares with the standard data | dagger whether it meets the corresponding test results.)
- 2020-10-24 12:27:23下载
- 积分：1
-
EEMD
说明： 应用labview实现信号的改进经验模态分解，对初学者有所帮助(Labview is applied to realize the improved empirical mode decomposition of signal, which is helpful for beginners)
- 2019-05-06 14:44:43下载
- 积分：1
-
CAR
模拟的智能小车控制系统,含有账户管理，密码修改(Simulation of smart car control system simulation of smart car control system)
- 2021-04-21 22:08:49下载
- 积分：1
-
大恒摄像头ocx文件及labview程序
labview编程实现相机数据采集，并进行简单识别(Daheng camera OCX file and LabVIEW program)
- 2018-08-22 14:13:02下载
- 积分：1
-
autocorrelationfunction
基于LabVIEW的时域分析_自相关函数(autocorrelation function)
- 2020-11-14 09:29:44下载
- 积分：1
-
crc32
I was suprised LabVIEW didn t had the CRC32. So I made it, http://en.wikipedia....edundancy_check, http://www.ietf.org/rfc/rfc1952.txt. It can take a array of U32, one element of U32 or a string. When needed I can create more CRC checks, CRC8, CRC16, etc... but CRC32 is the most used one I readed.
- 2014-10-03 08:36:43下载
- 积分：1
-
readCSVandwrite
说明： 通过读取本地CSV文件，筛选里面数据后，传输至指定数据库(By reading the local CSV data, it is transmitted to the database.)
- 2019-04-02 22:43:52下载
- 积分：1
-
power_analyse
此源程序为用Labview程序编制的，针对采集信号的功率进行分析。(The source code for the use of Labview programming, and for collecting the signal power for analysis.)
- 2020-11-07 15:19:48下载
- 积分：1
-
FFT
使用labview实现了FFT的变换，此方法更为简单快捷，同时简单明了(Labview achieved using FFT transform, this method is more simple and quick, and simple)
- 2021-04-17 14:58:53下载
- 积分：1
-
3.4
延时线的程序，能够实现单轴位移台的位移从而实现延时的效果，获得数据(Delay line program, it is possible to achieve the displacement of the uniaxial displacement station in order to achieve the delay effect, obtain data)
- 2013-04-01 13:41:01下载
- 积分：1
