登录
首页 » DOS » PLC

PLC

于 2010-01-14 发布 文件大小:323KB
0 188
下载积分: 1 下载次数: 16

代码说明:

  西门子s7-300课程设计搅拌器设计应用(english)

文件列表:

PLC实例
.......\十字路口的交通指挥信号灯.doc
.......\双缸顺序动作控制程序.doc
.......\多种液体自动混合装置的PLC控制.doc
.......\电梯控制.doc
.......\自动售货机.doc
.......\霓虹灯广告屏控制器的设计.doc

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • stc12C5410AD
    STC12C5410AD 参数 使用手册
    2010-01-03 15:56:36下载
    积分:1
  • 7290
    说明:  7290显示 7290显示 7290显示(7290 show revealed 7,290 7,290 7,290 showed 7290 show revealed)
    2006-02-27 16:11:54下载
    积分:1
  • 音乐频谱分析fft
    为快速傅里叶变换用c语言在51单片机中实现(Realization of Fast Fourier Transform with C Language in 51 Single Chip Microcomputer)
    2020-09-09 15:38:01下载
    积分:1
  • data_analysis
    Matlab Data analysis document
    2014-01-03 23:07:26下载
    积分:1
  • crazyflie四轴飞行器电路原理图、CAD文件
    开源无人机平台 crazyflie 的 原理图(Schematic of the open source drone platform crazyflie)
    2020-10-22 18:47:22下载
    积分:1
  • 11
    NUAA微机实验课设:1.密码确认。2.数据采集控制系统。3.数码管显示(NUAA Computer Lab located: a password confirmation. 2 Data acquisition and control system. 3 digital display)
    2014-01-16 23:02:47下载
    积分:1
  • RSBY-ECIS-Patch-1.0-13092013
    none1.The content is too simple 2.Is not a sourcecode or document 3.lost some files 4.Description is not detailed or not correct 5.Compressed file has password 6.Sourcecode duplicate or already exist Please do not upload copyrighted content and the file which has trojan or virus
    2014-01-17 23:51:05下载
    积分:1
  • NRF24l01
    系统平时处于循环接收检测状态,当有按键动作后发送数据 ,对方收到数据后LED闪烁, 任何一方可以发数据也可以收数据。 1. 当检测到按键动作后发送数据,自身LED闪烁 2. 当收到数据后LED闪烁 (Usually in the loop receiver detect state data, send keystrokes LED flashes after receipt of this data, either party can send data can also receive data. 1. When sending data detected keystrokes own LED flashes. LED flashes when data is received)
    2013-01-24 13:46:05下载
    积分:1
  • MPU9250
    A program for reading data mpu9250 sensor
    2016-09-22 21:14:40下载
    积分:1
  • speed
    采用霍尔传感器3020T,根据霍尔效应原理,在电机转轴边沿上放一永久磁钢,转轴附近放一个别3020T,当转轴旋转时,受磁钢的影响,霍地尔器件输出脉冲信号,送至单片机中断引脚,转速计数加1,单片机内部产生5s的定时,计算出1分钟的转速,送至显示单元,(Using Hall sensors 3020T, according to Hall-effect principle, the motor shaft of a permanent magnet placed on the edge, do not put a shaft near the 3020T, when the shaft rotates by magnet effect, HUO Di Seoul device output pulse signal, sent to microcontroller interrupt pin, speed count plus 1, the microcontroller internally generated timing 5s to calculate the speed of 1 minute, sent to the display unit,)
    2010-12-18 22:35:31下载
    积分:1
  • 696518资源总数
  • 106174会员总数
  • 31今日下载