-
bpyyyyyyyyy
本程序是基于bp神经网络的分类程序
开发环境是matlab(matlab)
- 2009-05-24 18:07:26下载
- 积分：1
-
10153597dsb
说明： 通信原理方面的一些基础matlab程序,包含数字基带传输系统中升余弦滚降系统,最佳基带系统,基带信号眼图,OOK,2PSK,2FS,MPSk,DSB,SSB,VSB(Some basic matlab programs of communication principle, including up-cosine roll-down system in digital baseband transmission system, optimal baseband system, baseband signal eye diagram, OOK, 2PSK, 2FS, MPSk, DSB, SSB, VSB)
- 2018-12-29 20:14:57下载
- 积分：1
-
PUMA560
用Robotics Toolbox for MATLAB做的一个PUMA560机器人的仿真界面，可以仿真运动学的正逆问题和动力学正逆问题，轨迹规划等问题(
With the Robotics Toolbox for MATLAB simulation interface to do a PUMA560 robot can simulate forward and inverse kinematics and dynamics problems are inverse problems, trajectory planning and other issues)
- 2014-04-13 22:31:49下载
- 积分：1
-
matlab_fluid
matlab编写的流体计算和传热程序，大家参考以下吧，或许有用(matlab prepared and heat transfer fluid calculation procedures, refer to the following U.S. right, perhaps useful)
- 2008-05-20 23:03:52下载
- 积分：1
-
Fig.5
Stud. Appl. Math. 118, 153-197 (2007)关于solitons的一篇文章，位图figure5的编程(Stud. Appl. Math. 118, 153-197 (2007) on the solitons in an article, bitmap figure5 Programming)
- 2010-03-11 10:20:05下载
- 积分：1
-
floc-esprit
在脉冲噪声情况下，基于分数低阶统计量的循环平稳信号的波达方向估计(In the case of impulse noise, DOA fractional lower order statistics of cyclostationary signal estimate)
- 2015-06-03 10:54:58下载
- 积分：1
-
DM642EDMA
This program uses the timers to trigger EDMA events. These events in turn
* trigger linked EDMA parameter tables to fill a ping pong buffer structure.
* Set a breakpoint on swiProcessFunc(int arg). Then open two memory windows.
* Use ping as the address for one memory window and pong for the other. Then
* run the application. You ll note that the program bounces between the ping
* and pong buffers filling each with a value that comes from the source. The
* source in this case is the SDRAM timer control register and it simulates
* input data(This program uses the timers to trigger EDMA events. These events in turn* trigger linked EDMA parameter tables to fill a ping pong buffer structure.* Set a breakpoint on swiProcessFunc (int arg). Then open two memory windows.* Use ping as the address for one memory window and pong for the other. Then* run the application. You' ll note that the program bounces between the ping* and pong buffers filling each with a value that comes from the source. The* source in this case is the SDRAM timer control register and it simulates* input data)
- 2010-08-07 11:34:58下载
- 积分：1
-
maidongfeng
模拟高耸结构的随机风载荷，风速时程，风载荷时程(Analog towering structures to random wind loads, wind speed time)
- 2013-09-13 11:46:04下载
- 积分：1
-
easy_classic_kalman_filter
经典的使用Kalman filter的程序，快速掌握kalman的技术 (classic easy program for kalman filter)
- 2013-03-04 00:10:51下载
- 积分：1
-
RLS
用MATLAB实现高斯白噪声系统输入信号的随机输出(Gaussian white noise with a MATLAB implementation of the random input output system)
- 2010-11-21 10:55:26下载
- 积分：1
