-
mie_scattering
说明： 通过mie级数计算球体的消光截面，散射截面，吸收截面(Mie series by calculating the extinction cross section sphere, scattering cross section, absorption cross section)
- 2011-04-11 16:27:32下载
- 积分：1
-
matlabForcast
matlab时间序列预测，本程序采用遗忘因子算法的方式实现(Matlab time series prediction that the adoption of the forgotten factor algorithm in a way)
- 2007-03-25 14:55:51下载
- 积分：1
-
rcs_frequency
雷达rcs是雷达的重要参数，为此编写了雷达rcs随频率的变化关系。方便新入门的了解rcs在不同情况下的特征(Radar rcs important parameters of the radar, for the preparation of the Radar rcs variation with frequency. Understanding rcs facilitate new entry characteristics in different cases)
- 2020-11-04 19:19:52下载
- 积分：1
-
zhikuo_bpsk
这是一个无线通信中最常应用的直接序列扩频的程序(direct spread spectrum)
- 2012-10-15 19:11:41下载
- 积分：1
-
simulink_sEMG_gesturerec
利用myo采集肌电信号和角速度信息，实现实时的手势识别(EMG acquisition and use of myo angular velocity information, real-time gesture recognition)
- 2020-12-21 12:19:08下载
- 积分：1
-
sensiu_v60
是一种双隐层反向传播神经网络，针对EMD方法的不足,相参脉冲串复调制信号。( Is a two hidden layer back propagation neural network, For lack of EMD, Complex modulation coherent pulse train signal.)
- 2016-09-01 15:36:21下载
- 积分：1
-
sin_interp
Star Code for signal processors. Generating a sine wave interpolated.
- 2010-06-27 05:43:54下载
- 积分：1
-
texturefeatures
说明： 这个程序是纹理特征提取的提取，很实用的程序(This procedure is the extraction of texture feature extraction, the procedure is very useful)
- 2011-03-24 11:06:39下载
- 积分：1
-
功率谱繁衍生成时域序列随机风 kaimal_spectrum
功率谱繁衍生成时域序列随机风-谐波合成法(Generate Random wind)
- 2021-02-23 01:29:41下载
- 积分：1
-
activeContoursSnakesDemo
本演示实现了主动轮廓模型由Kass等人提出。
要运行它的图形用户界面
1。基于MATLAB型引导提示。
2。关于“到现有的图形用户界面，点击”
3。选择在与本文件相同的目录snk.fig文件
4。按一下上方的绿色箭头启动图形界面
一旦GUI已经启动，您可以通过使用蛇
1。点击“新形象”，并加载输入图像。提供的样品图像。
2。平滑参数设置“西格玛”或保留其默认值并点击“过滤器”。这将平滑图像。
3。只要你点击“过滤器”，头发会出现交叉，用他们和你左击鼠标，您可以选择在图像上的初始轮廓的位置。会出现一个红色圆圈到处您单击并在多数情况下，你应该单击对象周围的一切你想要的部分。最后一点，必须挑选使用右键单击，以阻止更多的积分为MATLAB的要求。
4。设置各种蛇参数（在能源方面的相对权重的蛇目标函数）或离开它们的默认值，然后按一下他们“迭代”按钮。蛇会出现和移动，因为它收敛到它的低能量状态。(This demo implements the Active Contour Models as proposed by Kass et al.
To run it with GUI
1. Type guide on the matlab prompt.
2. Click on "Go to Existing GUI"
3. Select the snk.fig file in the same directory as this file
4. Click the green arrow at the top to launch the GUI
Once the GUI has been launched, you can use snakes by
1. Click on "New Image" and load an input image. Samples image are provided.
2. Set the smoothing parameter "sigma" or leave it at its default value and click "Filter". This will smooth the image.
3. As soon as you click "Filter", cross hairs would appear and using them and left click of you mouse you can pick initial contour location on the image. A red circle would appear everywhere you click and in most cases you should click all the way around the object you want to segment. The last point must be picked using a right-click in order to stop matlab for asking for more points.
4. Set the various snake paramete)
- 2010-07-05 11:54:13下载
- 积分：1
