-
MBD
基于Matlab/Simulink的自动代码生成书籍，对学习自动代码生成非常有帮助(Based on Matlab/Simulink automatic code generation books, learning automatic code generation is very helpful)
- 2017-05-17 16:51:44下载
- 积分：1
-
balanceeee
balance code of a infix notification..this code balance the infix..try it
- 2011-08-06 04:57:12下载
- 积分：1
-
oscilloscope_embedded_code
该嵌入式C语言源代码软件工程是以STM32F103系列微控制器为核心的嵌入式数字示波器的源代码工程，主要实现0V基线对齐、探头补偿校准、波形保存和调出等功能，具有带宽0-200KHZ、垂直灵敏度10mv/div-5v/div、记录长度1024点、触发方式自动/常规/单次等参数。(The embedded C language source code software engineering is based on STM32F103 series microcontrollers as the core of the embedded digital oscilloscope source code project, the main realization of 0V baseline alignment, probe compensation calibration, waveform preservation and recall functions, with bandwidth 0- 200KHZ, vertical sensitivity 10mv / div-5v / div, record length 1024 points, trigger mode automatic / conventional / single and other parameters.)
- 2017-08-23 11:53:40下载
- 积分：1
-
IAPTest
LPC ARM7的IAP测试实验，在EASYARM2100开发板上测试通过(LPC ARM7 the IAP test experiments, the development board test in EASYARM2100)
- 2020-09-04 15:48:07下载
- 积分：1
-
STM32
说明： stm32f103c8t6,驱动TM1650ESP8266串口蓝牙，内部flash读写，AT指令处理驱动(Stm32f103c8t6, driving tm1650 esp8266 serial port Bluetooth, internal flash reading and writing, at command processing driver)
- 2021-03-31 15:39:09下载
- 积分：1
-
STM32F103CDE
STM32F103CDE 中文说明书 对开发者 初学者都有好处(STM32F103CDE chinese document~)
- 2010-05-17 09:13:48下载
- 积分：1
-
stm32_soldering_iron_controller-master
使用stm32控制的T12焊台源代码，来自网海(Source Code of T12 Welding Platform Controlled by stm32)
- 2020-06-21 18:20:02下载
- 积分：1
-
AVR230_source
This is a simple bootloader for AT91SAM7 processors. It
permits you to download new code to the device over USB. This bootrom is
installed at address 0x00000000 in the ARM, which means that it is the
first piece of code to execute after reset. At startup, it waits for
a few seconds to see if the downloader is trying to connect. If not,
then the bootloader gives up control and jumps to your program. If the
downloader is trying to connect, then the bootloader receives the new
program over USB and writes it into flash.(This is a simple bootloader for AT91SAM7{S,X}{64,128,256} processors. It
permits you to download new code to the device over USB. This bootrom is
installed at address 0x00000000 in the ARM, which means that it is the
first piece of code to execute after reset. At startup, it waits for
a few seconds to see if the downloader is trying to connect. If not,
then the bootloader gives up control and jumps to your program. If the
downloader is trying to connect, then the bootloader receives the new
program over USB and writes it into flash.)
- 2009-11-17 10:47:55下载
- 积分：1
-
BHS STM32 实验29-CAN通讯 (直接操作寄存器)
准备两个CAN板子，连接两个CAN接口，两个板子都下载本程序。
本实验通过CAN总线控制另外一个板子的LED2~LED5闪烁的例子，如果通信正常可以看到两个板子的LED都再闪烁，
如果通信失败或者断开通信线，LED不再闪烁(Prepare two CAN board, connecting the two CAN interface, two board are download the program.
This experiment through the CAN bus control another board LED2 ~ LED5 flashing example, if communication normal CAN see two board LED twinkle again,
If communication failure or off the line, LED will no longer flash)
- 2012-04-16 14:13:56下载
- 积分：1
-
SD_FatFS
STM32F407ARM嵌入式SD卡烧写程序(SD card_program)
- 2015-01-04 22:30:47下载
- 积分：1
