-
hough
说明： 这个是MATLAB实现Hough变换的程序。有基本的Hough变换的理解程序，也有使用Hough变换来检测信号的程序(This is the realization of Hough Transform MATLAB procedures. Hough transform a basic understanding of procedures, have also used the Hough transform to detect the signal process)
- 2008-10-19 15:39:00下载
- 积分：1
-
FNN
我在这里有一个基于matlab的RNN递归网络源代码，希望和大家一起分享(I have a Matlab-based RNN recursive network source code, I hope to share with everyone)
- 2012-04-22 11:40:11下载
- 积分：1
-
binary-symmetric-channel-
用MATLAB SIMULINK实现BSC二进制对称信道建模和误码率测试模型(BSC in MATLAB binary symmetric channel bit error rate modeling and testing model)
- 2011-06-30 13:07:41下载
- 积分：1
-
matlab-cpp-cSharp-java
MATLAB与外部程序接口，直接调用matlab的算法很方便，推荐使用(MATLAB interface with external programs)
- 2015-01-14 16:36:48下载
- 积分：1
-
使用Matlab的M语言写的基带AMI编码程序-exam3_ami
使用Matlab的M语言写的基带AMI编码程序(use Matlab language to write the M-band coding procedures AMI)
- 2005-04-08 17:09:27下载
- 积分：1
-
activeContoursSnakesDemo
本演示实现了主动轮廓模型由Kass等人提出。
要运行它的图形用户界面
1。基于MATLAB型引导提示。
2。关于“到现有的图形用户界面，点击”
3。选择在与本文件相同的目录snk.fig文件
4。按一下上方的绿色箭头启动图形界面
一旦GUI已经启动，您可以通过使用蛇
1。点击“新形象”，并加载输入图像。提供的样品图像。
2。平滑参数设置“西格玛”或保留其默认值并点击“过滤器”。这将平滑图像。
3。只要你点击“过滤器”，头发会出现交叉，用他们和你左击鼠标，您可以选择在图像上的初始轮廓的位置。会出现一个红色圆圈到处您单击并在多数情况下，你应该单击对象周围的一切你想要的部分。最后一点，必须挑选使用右键单击，以阻止更多的积分为MATLAB的要求。
4。设置各种蛇参数（在能源方面的相对权重的蛇目标函数）或离开它们的默认值，然后按一下他们“迭代”按钮。蛇会出现和移动，因为它收敛到它的低能量状态。(This demo implements the Active Contour Models as proposed by Kass et al.
To run it with GUI
1. Type guide on the matlab prompt.
2. Click on "Go to Existing GUI"
3. Select the snk.fig file in the same directory as this file
4. Click the green arrow at the top to launch the GUI
Once the GUI has been launched, you can use snakes by
1. Click on "New Image" and load an input image. Samples image are provided.
2. Set the smoothing parameter "sigma" or leave it at its default value and click "Filter". This will smooth the image.
3. As soon as you click "Filter", cross hairs would appear and using them and left click of you mouse you can pick initial contour location on the image. A red circle would appear everywhere you click and in most cases you should click all the way around the object you want to segment. The last point must be picked using a right-click in order to stop matlab for asking for more points.
4. Set the various snake paramete)
- 2010-07-05 11:54:13下载
- 积分：1
-
c
说明： 约瑟夫问题的实现：设有n个人围坐在圆桌周围，现从某个位置m（1≤m≤n）上的人开始报数，报数到k的人就站出来。下一个人，即原来的第k+1个位置上的人，又从1开始报数，再报数到k的人站出来。依此重复下去，直到全部的人都站出来为止。试设计一个程序求出出列序列。(Joseph realized the problem: There are n people sitting around the round table, is from a position of m (1 ≤ m ≤ n) reported on the number of people began to be reported to the k number of people to come forward. The next person, that is, the original positions on the first k+1 people, and from the number reported at 1, then the number reported to the k to stand up. So repeat this until all the others can stand up. Try to design a program derived from the column sequence.)
- 2011-03-23 15:36:50下载
- 积分：1
-
Signal_lms
LMS算法实现自适应均衡器的MATLAB编程代码(matlab code of LMS algorithm )
- 2012-05-11 14:23:44下载
- 积分：1
-
3
反演自适应动态滑模控制，可以有效降低抖振(Inversion adaptive dynamic sliding mode control can effectively reduce the chattering)
- 2013-10-11 16:29:22下载
- 积分：1
-
ICA
模式识别特征提取中的独立成分分析算法的matlab源码(Independent component analysis)
- 2015-04-06 18:49:09下载
- 积分：1
