-
aircraft-control-system-research
说明： 吴树范的论文，飞机的总能量控制系统的研究(aircraft control system research)
- 2011-03-10 10:53:37下载
- 积分：1
-
Codes
First a estimate of wireless sensor nodes is made and a network mesh will be created based on some topology techniques. A connection has to be established between Node I and all the vicinity nodes.
- 2013-04-23 22:33:13下载
- 积分：1
-
fuzzypid
永磁同步电机模糊PID控制。含对比的PI控制的模型。实现了模糊控制算法，可以得到比单纯的PID更好的控制效果.(Fuzzy PID control of permanent magnet synchronous motor. Model PI-containing contrast control. Realization of fuzzy control algorithm can be better than a simple PID control.)
- 2020-11-20 14:59:38下载
- 积分：1
-
correlation
求各时域信号之间的频域相关性。包含互功率谱、相关系数频谱和相位相关频谱的计算(Seeking a frequency domain correlation at each time-domain signal. Contains crosspower, calculate the correlation coefficient spectrum and phase correlation spectrum)
- 2016-05-24 14:16:40下载
- 积分：1
-
PSO_Codes-Basic-Code
This Code SimulTION PSO BASIC CODE IN MATLAB IS CODE IS VWRY USEFUL FOR UNDERESTAND PSO HOW WORK
- 2013-03-03 21:41:29下载
- 积分：1
-
EMD
Hilbert-huang变换代码,主要实现HHT变换中EMD分解的Matlab程序，已经通过实际调试，附运行效果bmp图，若参数稍加修改，可对不同信号进行多模态分解。(HHT transform EMD decomposition Matlab program, through the actual commissioning, operating results bmp attached map parameters slightly modified, different signals can be multi-modal decomposition.)
- 2011-10-11 15:34:59下载
- 积分：1
-
matlab-introduction
武汉大学matlab课程课件，仅供学习交流(Wuhan University matlab courseware, only to learn communication)
- 2014-01-14 10:14:24下载
- 积分：1
-
MATLAB-trans-Edge
以MATLAB將影像做邊緣偵測以及邊緣強化，
邊緣偵測分別為Prewitt以及Canny，
邊緣強化是將邊緣做銳利化(MATLAB will do to the image edge detection and edge enhancement, edge detection, respectively Prewitt and Canny, edge enhancement is done to sharpen the edge)
- 2013-08-28 23:18:05下载
- 积分：1
-
bkpulseexport
直接读取振动噪声分析软件bk pulse文件，将测试组和函数组导出来，方便对测试数据进行后处理(his GUI runs Pulse Labshop in the backround (not visible) through an activex server. Exporting measurements using B&K Pulse s software is extremely tedious, requiring much mouse-clicking (setting measurement marks, following measurement marks, etc.). This GUI is relatively straightforward- your .pls file(s), type in the function name you wish to export along with its correpsonding function group, and list all of the measurement names you wish to export. Each function is exported to a single file within a folder that is created of the same name as the .pls file.)
- 2015-01-24 09:05:29下载
- 积分：1
-
ImageProcessingUsingMATLAB
image processing using matlab book
- 2010-11-09 03:59:48下载
- 积分：1
