-
jiefangcheng
求解线性方程组的几种方法：高斯列主元、高斯塞德尔迭代法(Solving linear equations in several ways: column pivot Gauss, high Sise del iteration)
- 2010-12-01 20:53:47下载
- 积分：1
-
Hamming1
hamming code but run correct
- 2014-10-25 00:40:24下载
- 积分：1
-
matlab
灰色处理，预测模型，GM(1,1)一次累加(Gray processing, prediction model)
- 2012-09-01 00:37:28下载
- 积分：1
-
S变换
说明： 用S变换对电压暂降进行检测，得到基频幅值，相位跳变，突变点，谐波检测，频率幅值包络线等特征量(The S-transform is used to detect the voltage sag, and the characteristic parameters such as fundamental frequency amplitude, phase jump, mutation point, harmonic detection, frequency amplitude envelope are obtained)
- 2021-03-29 15:29:10下载
- 积分：1
-
G_P_xjx
混沌G_P算法，用来计算LnC与Lnr的关系图(algorithm used to calculate LnC relations with the map Lnr)
- 2006-05-26 15:48:47下载
- 积分：1
-
Load_V2.0
此程序根据王专利撰写的《翼面结构有限元模型节点气动载荷计算》编写
需要的前期准备文件：case01.txt---已知不同工况下各个载荷点力的文件
Force_Site.txt---已知各个载荷点的坐标
Node_Site.txt----有限元节点坐标
输出文件 Nodal_Force_01.txt----存放每个有限元节点计算后分得的力，第一列为节点编号，第二列为节点力大小(This process patent under the king wrote " wing structural finite element model node aerodynamic load calculation" Writing required preparatory documents: case01.txt-- known under different conditions of each load point force file Force_Site. txt--- known each load point coordinates Node_Site.txt---- finite element nodal coordinates output file Nodal_Force_01.txt---- storage node finite element calculation for each share of power, first as the node number, the second column is the size of nodal forces)
- 2013-10-14 22:37:15下载
- 积分：1
-
matlab
里边包含了一个如何区分6和9的代码以及用最小距离法、梯度法以及K-NN方法对样本进行的分类代码(Inside contains an example of how to distinguish between 6 and 9, as well as the code with the minimum distance method, the gradient method and K-NN method for sample classification codes)
- 2014-12-11 23:12:22下载
- 积分：1
-
moxingyuece3
高速铁路路基沉降是一个复杂的系统过程,涉及不同时期、不同工况,选用单一的预测模型不足以反映路基整体的变形规律.Logistic模型及Verhulst模型的曲线均为S形,可以反映全过程的地基沉降与时间的关系.针对路基填筑期和降水期两个时段利用MATLAB软件编制程序计算模型参数,得到Logistic模型和灰色Verhulst模型,进而求得两者的最优加权组合模型.对比结果表明:在路基填筑期由两者的最优加权组合模型预测得到的结果与实测结果较吻合,拟合精度高于单一模型 而在降水期Verhulst模型的预测值更接近实测值,平均相对误差约为1.75％,拟合精度较高.(High-speed railway subgrade settlement process is a complex system involving different times and in different conditions, the choice of a single forecasting model does not adequately reflect the overall deformation of roadbed. Curve Logistic model and Verhulst models are S-shaped, the whole process can be reflected foundation settlement versus time. against roadbed construction period of two hours and precipitation using MATLAB software programming model parameters, the Logistic model and gray Verhulst model, and then get the optimal model of a weighted combination of the two. comparative results indicate : results and experimental results in the roadbed construction period by the weighted combination of the best of both models predicted than the anastomosis fitting accuracy than a single model precipitation predicted value of Verhulst model closer to the actual value of the average relative error approximately 1.75 fitting accuracy.)
- 2014-01-10 17:30:42下载
- 积分：1
-
capacity_DF2
用matlab实现DF MIMO双跳系统模型的容量仿真，并实现了蒙特卡罗仿真，对研究DF、MIMO有很好的参考价值。(Using matlab to achieve DF MIMO capacity of dual-hop system model simulation, and implemented Monte Carlo simulation, the study of DF, MIMO have a good reference value.)
- 2009-09-14 09:58:59下载
- 积分：1
-
ACpitch
采用自相关法提取基音周期，提取周期与实际值误差较小(Using autocorrelation method to extract the pitch period extraction cycle with the actual value of the error is smaller)
- 2013-01-13 14:37:47下载
- 积分：1
