-
STBC-OFDM
STBC-OFDM的matlab仿真程序。(STBC-OFDM in matlab simulation program.)
- 2010-01-04 13:07:59下载
- 积分：1
-
GA
本文通过运用matlab工具，编写了一个运用遗传算法解决方程最值问题的程序。(the process of GA model)
- 2013-05-06 14:52:11下载
- 积分：1
-
K_Means
K_Means聚类算法matlab实现，包含三个子函数，可用在图像处理中(K_Means clustering algorithm matlab realize, including three sub-functions that can be used in image processing)
- 2014-01-03 14:42:55下载
- 积分：1
-
air_sea
air-sea动量交换等海洋科学研究的有用软件,由网上搜集得到(air-sea momentum exchange of useful marine scientific research, software, collected from the Internet)
- 2009-03-14 10:42:38下载
- 积分：1
-
fso_guangpanchengxu
优化算法配套的程序代码，可直接运行，资料很全(Optimization matching code can be run directly, the information is all)
- 2010-09-05 21:20:18下载
- 积分：1
-
untitled1
变频调速系统仿真搭建模型 由于观测仿真波形 记录以及分析实验结果(Variable speed control system simulation build the observation model simulation and analysis of experimental results wave record
)
- 2012-05-29 12:32:14下载
- 积分：1
-
dianyaPWMnibian
三相电压型PWM逆变器的数学模型和主电路设计 完整三相电压型PWM逆变器模型 双闭环 (Mathematical model of three-phase voltage-type PWM inverter main circuit design and complete a three-phase voltage-type PWM inverter model dual-loop)
- 2014-12-10 11:56:42下载
- 积分：1
-
main2
一维高斯函数拟合，分析其方差和期望、残差平方和、决定系数等(Guass fitting)
- 2014-12-15 10:41:55下载
- 积分：1
-
matlab
聚类算法，不是分类算法。分类算法是给一个数据，然后判断这个数据属于已分好的类中的具体哪一类。聚类算法是给一大堆原始数据，然后通过算法将其中具有相似特征的数据聚为一类。这里的k-means聚类，是事先给出原始数据所含的类数，然后将含有相似特征的数据聚为一个类中。所有资料中还是Andrew Ng介绍的明白。首先给出原始数据{x1,x2,...,xn}，这些数据没有被标记的。初始化k个随机数据u1,u2,...,uk。这些xn和uk都是向量。根据下面两个公式迭代就能求出最终所有的u,这些u就是最终所有类的中心位置。(Clustering algorithm, not a classification algorithm. Classification algorithm is to give a figure, and then determine the data belonging to a specific class of good which category. Clustering algorithm is to give a lot of raw data, and then through the algorithm which has similar characteristics data together as a class. Here k-means clustering, is given in advance the number of classes contained in the raw data, then the data contain similar characteristics together as a class. All information presented in or Andrew Ng understand. Firstly, raw data {x1, x2, ..., xn}, the data is not labeled. K random initialization data u1, u2, ..., uk. These are the vectors xn and uk. According to the following two formulas can be obtained final iteration all u, u is the ultimate all these classes the center position.)
- 2014-02-18 09:59:02下载
- 积分：1
-
Glide_slope
root locus of glide slope using matlab
- 2010-10-18 14:05:50下载
- 积分：1
