-
mynlms-and-myrls
此文件包括mynlms和myrls，编程简单有效，是很好的程序(This file to include mynlms and myrls programming is simple and effective is a good program)
- 2012-06-18 19:02:39下载
- 积分：1
-
Fast-Fourier-Transform
FFT应用实例
产生一组信号，由两个频率为60Hz和150Hz的正弦信号和随机噪声叠加而成，(FFT application instanceproduce a set of signals, by two frequency is 60 hz and 150 hz sine signal and random noise,)
- 2015-12-28 19:25:29下载
- 积分：1
-
MSER
Maximally stable extremal regions (MEX MATLAB to C++) implementation
- 2011-07-13 01:06:29下载
- 积分：1
-
dljs
基于Matlab的电力系统短路计算程序，可在一定条件下计算出特定电力系统各支路的短路电流和个节电的短路电压(A program which based by matlab that fucking translation fucking english describ)
- 2013-12-31 15:45:51下载
- 积分：1
-
小波去噪
说明： 利用MATLAB产生正弦信号，加入高斯白噪声后利用小波变换技术去噪声(The sine signal is generated by MATLAB, and the noise is removed by wavelet transform after Gaussian white noise is added)
- 2021-03-22 09:45:33下载
- 积分：1
-
mtoc___mlfex_1.3
mtoc++ - Doxygen filter for Matlab and tools
- 2013-10-25 17:15:50下载
- 积分：1
-
Untitled_12
根据德布鲁意序列，编写的MATLAB代码，生成伪随机序列，继而转化为图片，图片中一定大小的图像块与其他任何相同大小的图像块都不同。(According to the de Bruges sequence, the MATLAB code is written to generate a pseudo-random sequence, which is then transformed into a picture in which a certain size of the image block is different any other image block of the same size.)
- 2016-12-22 16:49:49下载
- 积分：1
-
duru2
本代码是用来读取图像的，并把图像归入到一个矩阵中(This code is used to read the image and the image classified into a matrix)
- 2010-12-17 17:12:46下载
- 积分：1
-
IMCPIDA
IMC-PID是利用内模控制原理来对PID参数进行计算，获得参数(IMC-PID is the use of internal model control principle to the calculation of the PID parameters, access parameters)
- 2021-03-03 09:49:33下载
- 积分：1
-
Link-a-System-Level-OFDM-Simulator
针对OFDM系统，分成链路级仿真和系统级仿真两个部分。为了降低系统级仿真的复杂度，采用链路级仿真的部分结果。(It contains mainly two parts, i.e. link-level simulator and system-level simulator.
Link-level simulator focus on a single-cell single-user scenario, where signal is transmitted from tx, and estimated at rx. Comparing the difference in tx/rx signal, the error rate can be found out. The output of the link-level simulator is the BLER/BER vs. SNR mapping table, that can be used for the system-level simulation.
System-level simulator focus on a multi-cell multi-user scenario. For the sake of simplicity, it takes the mapping table aquired in the link-level simulation, measure the actural SNR, and finds the corresponding error rate.
Link-level simulator support SISO, 1 by x MRC, 2 by 1 STBC/SFBC, 2 by 2 Alamouti, x by 1 Antenna selection, x by y antenna selection.
System-level simulator, currently support only SISO and 1 by 2 MRC.
To start with, go into the folder sys_link_simu, and excute the following commond from matlab:
sys_link_simu_func(a,b)
where a is the link ada)
- 2011-08-09 11:00:53下载
- 积分：1
