-
optimization_cases_using_GA
说明： 运用遗传算法进行多元多峰函数优化，多目标问题优化！有案例！可以运行！(using Genetic Algorithm to test multi-peak function and multi-objective function.)
- 2010-05-03 14:49:34下载
- 积分：1
-
TA
说明： this is the simple code for a beginner matlab programming to make a plot, change the plot color, change the dot shape etc.
- 2011-05-13 11:51:44下载
- 积分：1
-
CtoF
Converter Celsius Fahrenheit for a temperature set by the user
- 2010-05-25 05:56:57下载
- 积分：1
-
cl
说明： matlab潮流计算，利用牛顿法计算线路潮流，各位大神进来指点(Matlab power flow calculation, using Newton method to calculate line power flow, you gods come in and give advice)
- 2019-05-05 14:15:47下载
- 积分：1
-
Matlab-simulation-DF-and-AF-source
该程序是使用Matlab仿真协同通信的DF（解码转发）基本性能，基本模型S-R-D三个节点，接收端使用MRC（最大比合并）。固定DF由于SR信道的错误，其性能受到限制，在大SNR情况下不能获得有效分集。而当SR距离足够近的时候，可能获得一定的分集增益。(The program is a cooperative communication using Matlab simulation DF (decode forwarding) basic performance, the basic model of the SRD three nodes, the receiver uses the MRC (maximum ratio combining). Fixed DF error of the SR channel, its performance is limited, can not obtain a valid diversity in the large SNR case. When the SR close enough, you may get some diversity gain.)
- 2012-04-19 14:48:23下载
- 积分：1
-
CAP10---Power-System-Stability-and-Control---P
CAP10 - High-Voltage Direct-Current Transmission - Power System Stability and Control - P. Kundur(1)
- 2015-03-18 19:38:28下载
- 积分：1
-
166565476
m/m/m排队模型的仿真，很好的资料！！(m/m/m queuing model of the simulation, very good information! !)
- 2009-06-06 17:47:01下载
- 积分：1
-
我编写的monte carlo随机数发生器检验程序
说明： 该程序用来检验monte carlo随机数的分布是否满足随机性要求。包括独立性检验、均匀性检验和参数检验。(procedures used to test the Monte Carlo random number distribution to satisfy the requirements randomness. Including the independence test, uniform test parameters and test.)
- 2005-09-24 13:30:04下载
- 积分：1
-
77433656timing_bit
位同步仿真，有仿真数据的输入，以及转换，可以输入到verilog中仿真(Bit synchronous simulation, simulation data input, and conversion, can be entered into the simulation verilog)
- 2011-08-11 22:12:30下载
- 积分：1
-
8259.asm
直接用手动产生单脉冲作为中断请求信号。 要求每按一次开关产生一次中断,在屏幕上 显示一次“TPCA Interrupt!”,中断10次后 程序退出(Directly by hand to produce a single pulse as an interrupt request signal. Each time you press the switch requires an interrupt is generated, show a TPCA Interrupt! On the screen, interrupted 10 times after the program exits)
- 2014-12-14 10:06:38下载
- 积分：1
