登录
首页 » matlab » Copy_of_constance_impedance

Copy_of_constance_impedance

于 2014-08-25 发布 文件大小:2KB
0 187
下载积分: 1 下载次数: 7

代码说明:

  constant impedance load modeling in a 11 bus distributiaon network , with power flow and linecurrent and busvoltage output

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • chap3
    vc++ 与matlab图像处理与识别案例精选(vc++ with matlab image processing and recognition of cases selected)
    2007-09-24 10:41:31下载
    积分:1
  • ofdmsystemmatlab
    说明:  基于能量检测和周期循环检测的认知无线电频谱检测matlab代码 用周期循环检测算法检测: 首先运行a.m程序,通过此程序运算得出循环频率a值; 再运行zhouqi.m程序,对a值进行确定,通过周期循环算法对信号进行检测; 用能量检测算法检测: 运行nengliang.m检测程序,使用能量检测对信号进行检测。 检测完毕,对检测性能进行分析。 (Cognitive radio based on energy detection spectrum detection matlab code)
    2011-04-14 11:16:47下载
    积分:1
  • movie
    source code matlab for image by using imageprocessing
    2011-05-08 18:55:07下载
    积分:1
  • induction-motor_ws-simulation
    This program is about inuduction motor s ws simulation (angular speed) with matlab codes.
    2011-12-04 04:24:08下载
    积分:1
  • mamdani_ipmt
    fuzzy controller design for inverted pendulum
    2014-01-25 15:54:50下载
    积分:1
  • g729
    G729编码和解码的Matlab源程序 调用方法: 1.需要编码时,在 Matlab命令行下输入"G729code(speech)"(请务必保证 speech是已经存在在 Matlab工作区的一个行向量,其中是语音数据),然后你会在你的文件夹下看到一个"coding.bit"的文件。 2.需要解码时,把"coding.bit"的文件复制到"G729 decoder"的目录下,在Matlab命令行下输入"G729decodermain",然后你会在文件夹下看到"syn_speech.wav",那就是重构语音。 enjoy it! (G729 encoding and decoding of the Matlab source code to call methods: 1. The need for coding at the Matlab command line, enter )
    2007-11-21 23:02:40下载
    积分:1
  • QDPSK
    QDPSK Communication Performance simulation
    2008-05-21 16:16:54下载
    积分:1
  • ravidrives
    control of induction motor by generating pwm pulses
    2011-01-09 07:26:56下载
    积分:1
  • OFDM rece matlab
    接收端采用的算法和程序流程与发送端发送的OFDM符号的帧结构有关系。具体的帧结构,以及定时估计,频偏估计,剩余误差跟踪的算法可参考算法说明文档。这里对程序的流程进行说明。 首先根据短训练字的特性进行相关运算,进行信号到达检测,当检测到相关值大于门限一定次数后,认为有信号到达。然后根据长训练字的特性,进行相关运算,进行OFDM符号FFT窗口起始位置的估计。估计出FFT窗口的位置后,先在时域进行小频偏的估计,将两个长训练字进行小频偏补偿后,进行FFT运算,根据FFT运算的结果进行整数倍频偏的估计。这些参数估计完成后,就可以进行数据解调了。先对数据部分进行完整的频偏补偿,然后根据估计的FFT窗口位置进行FFT运算得到频域的数据,进行解调。然后在对应于导频的子载波位置上提取出导频信息,根据导频信息估计出剩余定时误差以及剩余的信道响应误差,将误差量送入环路进行跟踪。当收到所有数据后,重新回到信号到达检测状态,进行下一次信号到达的检测和信号接收。 (The receiving end uses the algorithm and the program flow and the frame structure of the OFDM symbol transmitted by the sending end. Specific frame structure, and timing estimation, frequency offset estimation, residual error tracking algorithm can refer to the documentation. Here to illustrate the process of the program. First, according to the characteristics of the short training word correlation operation, the signal reaches the detection, when the correlation value is greater than the threshold of a certain number of times, that there is a signal to reach. Then, according to the characteristics of the long training word, the correlation operation is carried out, and the initial position of the OFDM symbol FFT is estimated. The estimated position of the FFT window, first in the time domain for small frequency offset estimation, two long training word for small frequency offset compensation, the FFT operation. According to the result of FFT for integer frequency bias estimation. Af)
    2020-11-05 00:19:52下载
    积分:1
  • mr
    说明:  matlab自回归马尔可夫转换模型仿真估计与预测(matlab autoregressive Markov switching model simulation estimates and projections)
    2009-04-28 10:16:01下载
    积分:1
  • 696518资源总数
  • 105584会员总数
  • 19今日下载