-
att7022
att7022设计方案,包括sch,asm,hex等(att7022 design programs, including sch, asm2, hex, etc.)
- 2021-04-09 11:29:00下载
- 积分：1
-
key
说明： 51单片机矩阵键盘程序
51单片机矩阵键盘程序
51单片机矩阵键盘程序
51单片机矩阵键盘程序(51 single-chip single-chip microcomputer 51 program matrix matrix keyboard keyboard keyboard matrix 51 SCM procedures procedures procedures keyboard matrix 51 SCM)
- 2021-04-23 16:58:47下载
- 积分：1
-
xymuc
单片机入门的40个实验.rar........(40 entry single-chip experiment. Rar ........)
- 2009-06-17 00:25:27下载
- 积分：1
-
seven_order5
fluent物性随温度变化的udf（包括导热和比热）；边界条件温度随时间变化的udf。(fluent physical properties with temperature changes udf (including thermal conductivity and specific heat) temperature boundary conditions change over time udf.)
- 2015-10-07 20:38:22下载
- 积分：1
-
1277168144
S3F9454 example
IAR Compiler use
timer0 ADconvert
- 2013-03-07 13:17:15下载
- 积分：1
-
12864
说明： lcd12864驱动文件，建议收藏！(LCD12864 driver file, recommended collection!)
- 2019-03-11 14:11:52下载
- 积分：1
-
实验13 TFT LCD显示实验
说明： 基于正点原子STM32F407的LCD显示实验(LCD Display Based on Positive Atom STM32F407 Explorer Platform)
- 2020-06-23 04:40:02下载
- 积分：1
-
uartdayin
msp430f5529串口打印程序，实现字符串的发送，用于gsm等。(//******************************************************************************
// MSP430F552x Demo- USCI_A0, 9600 UART, SMCLK, LPM0, Echo with over-sampling
//
// Description: Echo a received character, RX ISR used. Normal mode is LPM0.
// USCI_A0 RX interrupt triggers TX Echo.
// If UCOS16=1, UCBRx=Fbrclk/(16*Baudrate)
// Baud rate divider with UCBRx = 1MHz/(16*9600) = ~6.8
// ACLK = REFO = ~32768Hz, MCLK = SMCLK = default DCO = 32 x ACLK = 1048576Hz
// See User Guide for baud rate divider table
//
// MSP430F552x
// -----------------
// /|| |
// | | |
// --|RST |
// | |
// | P3.3/UCA0TXD|------------>
// | | 9600- 8N1
// | P3.4/UCA0RXD|<------------
//
// Bhargavi Nisarga
// Texas Instruments Inc.
// April 2009
// Built with CCSv4 and IAR Embedded Workbenc)
- 2013-08-06 09:13:20下载
- 积分：1
-
红外遥控带原理图
说明： 设计一个基于单片机的嵌入式系统，要求具备以下功能:
红外数据的接收及解码,红外发色电路
数码管的显示驱动控制
将接收到的红外数据进行实时显示(限于动态扫描方法)
请根据以上功能要求，进行硬件系统设计,编写软件程序并画出流程图。
信号波形解码显示都没问题，LED灯和蜂鸣器设计是有点问题的，可以删掉不用不影响。自动使用的是压缩包里第二个文件的程序，其他包里有额外的参考资料，可借鉴。(To design an embedded system based on MCU, the following functions are required:
Infrared data receiving and decoding, infrared color circuit
Display drive control of digital tube
Real time display of received infrared data (limited to dynamic scanning method)
According to the above functional requirements, design the hardware system, write the software program and draw the flow chart.
Signal waveform decoding display is OK, LED lights and buzzer design is a bit of a problem, can be deleted without affecting. Automatic use of the second file in the compressed package of the program, other packages have additional reference materials, can be used for reference.)
- 2020-07-10 11:42:29下载
- 积分：1
-
pcbjiance
待检测pcb板和标准pcb对比，然后对待测pcb腐蚀及膨胀处理，进行缺陷标注显示图像并输出焊盘缺失数，导线缺失数，短路数等。所以源图像均有，并再次测试无误，可以直接运行。(To be detected and the standard pcb board pcb contrast, then treat corrosion test pcb and the expansion process, defect labeling displays images and outputs missing number pad, missing a few wires, short circuit and number. So were the source image, and test again correctly, you can run directly.)
- 2021-04-27 17:28:44下载
- 积分：1
