登录
首页 » matlab » EditModel

EditModel

于 2013-03-07 发布 文件大小:3KB
0 200
下载积分: 1 下载次数: 1

代码说明:

  This is an example of EditModel

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • CP0902
    uwb无线电基础代码,第九章,超宽带信道与接收机,共四个程序。(based on UWB radio code, Chapter IX, ultra-wideband channel with the receiver, a total of four procedures.)
    2007-10-18 15:21:15下载
    积分:1
  • radar
    瑞利分布的气象雷达回波,时频分析,功率谱密度,频谱分布。(Rayleigh distribution of meteorological radar echo time-frequency analysis, power spectral density, spectral distribution.)
    2010-05-16 11:47:14下载
    积分:1
  • stripmapSAR
    SAR成像的程序,很完整,适合初学者入门(SAR imaging procedures, is very complete, suitable for beginners entry)
    2010-05-18 20:14:13下载
    积分:1
  • adjustBW
    Bandwidth (signal processing) or analog bandwidth, frequency bandwidth or radio bandwidth: a measure of the width of a range of frequencies, measured in hertz Bandwidth (computing) or digital bandwidth: a rate of data transfer, bit rate or throughput, measured in bits per second (bps) Spectral linewidth: the width of an atomic or molecular spectral line, measured in hertz
    2011-08-16 14:48:36下载
    积分:1
  • FDTD_CPML_3D
    是关于GPR正演模拟的FDTD-3D算法,加载完全匹配层吸收条件。。(It is the FDTD-3D algorithm for GPR forward modeling, loading the perfectly matched layer absorbing condition.)
    2018-04-22 15:07:09下载
    积分:1
  • spwmnpc
    npc 3-level inverter spwm matlab
    2021-04-19 15:58:51下载
    积分:1
  • pathPlanning
    基于蚁群算法动态寻路算法的matlab仿真程序(Dynamic routing based on ant colony algorithm matlab simulation program)
    2015-01-17 19:06:55下载
    积分:1
  • un2
    模拟数据分析处理的过程,应用simulink(simulink U)
    2012-03-26 09:55:40下载
    积分:1
  • exercise
    根据公式I(n-1)=(1-In)/n 令I11=0计算I1 到I10; 根据公式In=1-nI(n-1) 令I0=0.6321 计算I1到I7; 根据公式X2=a , 令a=2,计算X的值。(According to the formula I(n-1)=(1-In)/n ,set I11 equals zero,and count I1 to I10. According to the formula In=1-nI(n-1),set I11 equals zero,and count I1 to I10. According to the formula X square equals a ,set a equals two ,then calculate X )
    2010-05-09 21:54:01下载
    积分:1
  • TCM-MATLAB
    基于MATLAB的TCM编译码器的代码,包括Binary.m Decoder.m Demodulation.m Error_Pb.m Eu_distance.m Eu_distance.m。。等(MATLAB codec code based on TCM)
    2015-04-04 09:03:58下载
    积分:1
  • 696518资源总数
  • 106174会员总数
  • 31今日下载