-
dadi_zhijiao
GPS输出的经纬度坐标转换为大地直角坐标(GPS output of geodetic latitude and longitude coordinates is converted to Cartesian coordinates)
- 2021-03-12 17:19:25下载
- 积分:1
-
mud_code.tar
This code is for multiuser detection in communication
- 2009-06-05 20:02:54下载
- 积分:1
-
MildML_0.1-Matlab.tar
图像标注算法 MildML 的 matlab 代码, 多示例学习标注算法(image annotation algorithm of MildML in matlab code of <Multiple Instance Logistic Discriminant-based Metric Learning (MildML) and Logistic Discriminant-based Metric Learning (LDML)>)
- 2015-01-23 09:22:11下载
- 积分:1
-
Matlab code for VaR
说明: 给出了通过MATLAB计算VaR的各种方法和实例(MATLAB code for Value-at-risk)
- 2020-06-30 03:40:01下载
- 积分:1
-
matlabASKPSKFSK
数字信号的传输方式分为基带传输和带通传输,在实际应用中,大多数信道具有带通特性而不能直接传输基带信号。为了使数字信号在带通信道中传输,必须使用数字基带信号对载波进行调制,以使信号与信道的特性相匹配。这种用数字基带信号控制载波,把数字基带信号变换为数字带通信号的过程称为数字调制。通常使用键控法来实现数字调制,比如对载波的振幅、频率和相位进行键控。(Transmission of digital signals into base band transmission and band-pass transmission, in practice, most of the channel with band-pass characteristics can not directly transmit base-band signal. In order to make the digital signal is transmitted with a communication channel, you must use the digital baseband signal to modulate the carrier to make the signal to match the characteristics of the channel. The digital baseband signal control with a carrier, the digital baseband signal conversion to digital bandpass signal is called digital modulation. Keying method is commonly used digital modulation, such as on the carrier' s amplitude, frequency and phase shift keying.)
- 2010-11-14 16:08:52下载
- 积分:1
-
Nasser---Copy
operating research linear programing
- 2012-04-17 16:08:44下载
- 积分:1
-
DSP_Mitra_programs
these are matlab files for Mitra book
- 2013-03-11 18:19:35下载
- 积分:1
-
Signals-and-SystemsAnalysis-and-threalization-of-M
1. 该光盘包含了“信号与系统分析及MATLAB实现”一书的第十二章所有程序;
2. 为了方便读者阅读程序,所有程序均采用中文注释。MATLAB的程序编辑器不支持中文显示,用户只需在Word下直接打开源程序文件,即可阅读程序中的中文注释;
3. 程序文件的命名分为以下三种类型:
(1) 若为书中例题的程序,则程序文件名一律以ex开头,后面跟4位数字(前两位表示章号,后两位表示例题序号)表示的该程序所在例题的编号。例如,ex0603.m是例6.3的程序,而ex1102.m则是例11.2的对应程序。
(2) 若为书中图形的实现程序,则程序文件名一律以figure开头,后面跟4位数字(前两位表示章号,后两位表示图形序号)表示的该程序所绘图形的编号。例如,figure1203.m是实现图12.3的程序,而figure0710.m则是实现图7.10的对应程序。
(3) 若为函数文件,则直接以函数名命名,例如文件sconv.m即是书中函数sconv()的对应程序。
()
- 2008-06-06 11:42:47下载
- 积分:1
-
code
implement PRM to check collision robot and obstacle
- 2012-01-22 05:38:18下载
- 积分:1
-
BILINEAR-Interpolation
A code for implementing Bilinear Interpolation on Images
- 2014-01-31 20:22:44下载
- 积分:1