登录
首页 » matlab » edge-and-GUI

edge-and-GUI

于 2013-09-19 发布 文件大小:2348KB
0 208
下载积分: 1 下载次数: 18

代码说明:

  图像边缘检测,并有gui界面的设计 有matlab程序生成exe的部分内容(detection of the image edge and establish the gui)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • A-Guide-to-MATLAB-for-Beginners
    说明:  一本matlab初学者的入门级经典书籍编程人员案头必备的一本参考书籍,英文版,有助于提高英文及编程技术.(An entry-level matlab beginner programmers classic books necessary for a desk reference book, in English, help to improve English and programming.)
    2011-02-19 11:18:14下载
    积分:1
  • QLIV
    QILV calculation for finding similarity between two images
    2011-11-22 01:09:07下载
    积分:1
  • golaycodecs
    5/1/2012 - updated to implement extended Golay codes for stanag
    2012-01-06 00:41:47下载
    积分:1
  • svpwmvect
    a simulation of the svpwm of two levels inverters
    2010-07-28 23:36:54下载
    积分:1
  • ed
    说明:  edge detectoin using wavelet transform built in matlab for beguners and comprisions also.....
    2012-04-05 14:05:29下载
    积分:1
  • 项目4
    说明:  任务:设计一个4×2.5Gbit/s 长距离光纤传输系统,并利用OptiSystem 仿真验证。 要求: 1.采用波分复用技术,波长设置以100GHz 为间隔,频率分别为193.1THz、193.2THz、193.3THz、193.4THz,每个波长传输速率为2.5Gbit/s(NRZ),传输距离为300km。采用常规光纤,光纤损耗系数为0.25dB/km。 2.单通道光发送机最大输出功率为0dBm,光接收机的接收光功率不低于-26dBm,过载点为-10dBm。 3.可以采用EDFA 作为线路放大器,其中EDFA 的输入功率限制在-18~2dBm,最大输出功率20dBm,增益范围为13~25dB,噪声指数4.0dB。(Task: Design a 4 x 2.5 Gbit/s long-distance optical fiber transmission system, and use OptiSystem simulation to verify. Requirement: 1. Using wavelength division multiplexing technology, the wavelength is set at 100GHz intervals, with frequencies of 193.1 THz, 193.2 THz, 193.3 THz and 193.4 THz, respectively. The transmission rate of each wavelength is 2.5 Gbit/s (NRZ), and the transmission distance is 300 km. The loss coefficient of conventional optical fibers is 0.25dB/km. 2. The maximum output power of a single-channel optical transmitter is 0 dBm, and the receiving power of an optical receiver is not less than -26 dBm, and the overload point is -10 dBm. 3. EDFA can be used as line amplifier, where the input power of EDFA is limited to - 18-2dBm, the maximum output power is 20dBm, the gain range is 13-25dB, and the noise index is 4.0dB.)
    2019-05-13 09:39:41下载
    积分:1
  • project4
    基于matlab的直方图处理,增强细节处理效果,暗处细节可以得到更好体现,并显示处理前后的直方图(Matlab histogram processing to enhance the details of the treatment effect)
    2012-04-10 18:35:12下载
    积分:1
  • Matlab-sufaji
    matlab算法集,其中讲述了我们常用的一些算法,如弦截法、史蒂芬森法,B-F-S算法等等(matlab algorithm set, which tells us some of the commonly used algorithms, such as Secant Method, Stephenson France, BFS algorithm etc.)
    2014-09-11 13:05:13下载
    积分:1
  • SIFT_YantaoNoemie
    根据sift算法经典文章得到的matlab算法程序,可以直接运行。(According to the the sift algorithm classic article Matlab algorithm can be run directly.)
    2013-04-02 11:12:32下载
    积分:1
  • waicanshutiqu
    用于计算相机外参数,即CCD像素坐标与三维世界坐标的对应关系,输入参数是世界坐标标定点对,输出外参数矩阵(Outside the parameters used to calculate the camera, that the correspondence between CCD pixel coordinates and the coordinates of the three-dimensional world, the world coordinate input parameter calibration point right, outside the parameters of the output matrix)
    2014-01-02 17:33:09下载
    积分:1
  • 696518资源总数
  • 106148会员总数
  • 10今日下载