-
串口调试新
说明： 可实现串口的全双工功能，即接受和发送数据(It can realize full duplex function of serial port, i.e. receiving and sending data)
- 2020-04-28 09:56:01下载
- 积分：1
-
mppt控制仿真
说明： 此模型是基于matlab/simulink下的最大功率跟踪控制，能有效地追踪最大功率(This model is based on the maximum power tracking control under matlab/simulink, and can effectively track the maximum power.)
- 2019-03-22 20:28:54下载
- 积分：1
-
Signals--Systems-and-Transforms-4E-l
A Solution Manual for Signals, Systems and Transforms 4E l.Phillips John.M Parr Eve
- 2021-03-28 21:59:12下载
- 积分：1
-
LabVIEW-parallel-Demo
本Demo演示了LabVIEW图形化开发环境的并行编程模式。在并行循环之间可以通过队列或者是局部变量传递数据。基于队列的并行循环模式也叫做生产者/消费者模式。(This Demo demonstrates NI LabVIEW graphical development environment of parallel programming model. Between the parallel loop through the queue or a local variable data transmission. Queue based parallel circulation mode is also called the producer/consumer.)
- 2012-06-01 16:27:41下载
- 积分：1
-
第5章
说明： labview code, chapter five
- 2019-01-18 15:08:45下载
- 积分：1
-
基于LabVIEW的通用自动测试系统设计
基于LabvIEw的通用自动测试系统(ATs)舍计算机，可鳊程激励、响应数据采集及uuT模块，采用MxI总线控制方式。专用信号发生器为uuT提供模拟激励信号，矩阵开关和适配器完成不同信号间切换。主控计算机执行测试程序，信号发生器发送激励信号，数据采集卡采集数据，采集数据经调理后，并与标准数据|匕较是否满足相应测试结果。(The general automatic test system (ATs) based on LabvIEw can be used as a computer to excite, respond to data acquisition and uuT module. The control mode of MxI bus is adopted. Special signal generator provides analog excitation signal for uuT, matrix switch and adapter complete switching between different signals. The main control computer executes the test program, the signal generator sends the excitation signal, the data acquisition card collects the data, after the data acquisition is adjusted, and compares with the standard data | dagger whether it meets the corresponding test results.)
- 2020-10-24 12:27:23下载
- 积分：1
-
array-to-cluster
labvIEW程序，可以把一个数组转化为一个簇的形式(labvIEW program, you can put an array into a cluster)
- 2012-08-22 22:58:28下载
- 积分：1
-
server
LabVIEW里实现服务器功能，后面还有客户机(server)
- 2010-05-07 21:16:59下载
- 积分：1
-
depict
编写软件为labview2011，功能为读取txt文件中的值，并绘制电平图，设置了双游标，可以自动准确计算出两游标X轴时间差值。txt的内容为上升沿或下降沿的时间信息，首位0代表下降沿，1代表上升沿。后面位的值乘16代表沿的绝对时间(program software is the labview2011, functions is to read txt file values , and draw level diagram, set up a dual cursors, you can automatically and accurately calculate the time difference between the two cursors X axis. txt contents of rising or falling time information, the first 0 represents falling, a representative of the rising edge. Followed by 16-bit value represents absolute time along)
- 2013-08-08 10:44:10下载
- 积分：1
-
ICD-GPS-200C
GPS接口控制文件，GPS开发人员必备的手册(GPS Interface Control Document)
- 2021-03-25 15:09:13下载
- 积分：1
