-
bezier
本文说明了bezier曲线的渐进迭代性质，是对bezier曲线进行十次渐进逼近迭代，有图形效果来看一斤很接近所给的点(This article describes the iterative nature of the progressive bezier curve, is the bezier curve gradually approaching ten iterations, with graphics that look very close to a pound to the point)
- 2011-10-25 16:30:58下载
- 积分：1
-
CS
说明： 压缩感知matlab代码，使用FFT进行稀疏分解，OMP算法重建信号(Compressed sensing matlab code, the use of FFT for sparse decomposition, OMP algorithm for signal reconstruction)
- 2011-11-12 22:04:47下载
- 积分：1
-
AO_Protocol
关于短路计算的一些源程序同时是有关matlab优化的源程序(Short-circuit calculations on some of the matlab source code is also optimized source)
- 2011-11-28 10:52:43下载
- 积分：1
-
Cluster2_web
Towards Human Exploration of Space:
a EUropean Strategy
- 2013-12-07 21:49:27下载
- 积分：1
-
mxulie
产生m序列的源代码，为5级线性反馈移位寄存器，有兴趣的可以看看(Generate the source code of the m-sequence, five linear feedback shift register, interested can look at)
- 2013-05-13 07:09:51下载
- 积分：1
-
WhiteandcoloredNoise_series
利用白噪声序列和传递函数生成有色噪声的源代码，很实用(Using white noise sequence and colored noise transfer function to generate source code, very useful)
- 2014-01-15 11:13:16下载
- 积分：1
-
bysnet
说明： 基于matlab的贝叶斯网络预测模型，能够预测事件发生的概率。(Matlab based on Bayesian network model to predict the probability of events.)
- 2011-04-17 08:47:04下载
- 积分：1
-
svpwm
SVPWM 矢量控制系统仿真源码 没太看明白 大家试着看看吧(SVPWM vector control system based source did not quite understand this we try to look at it)
- 2011-05-29 03:27:01下载
- 积分：1
-
Auto_Measure_system
利用ccs环境、MATLAB环境、DSP（TMS320F2812)、被测对象和Agilient网络分析仪E5071B，构建一个自动测量系统。
相信大部分人都知道基于NI公司的GPIB总线，可以实现自动测量，但NI公司的方案实在太昂贵，采用MATLAB能够大大降低成本。matlab与ccs之间基于RTDX协议进行数据交换，同时matlab基于TCP/IP协议与E5071B之间通信，源码说明如下：
（1）RTDX_ok目录：matlab7.0代码，包含了一个用GUI实现的界面和相关的具体代码，特别是在其中实现了SCPI语言来对仪器进行控制。
（2）TMS320F2812目录：包含ccs下的c代码，如果没有做过RTDX的应用，相信这个对你很有启发。(Use ccs environment, MATLAB environment, DSP (TMS320F2812), the measured object and Agilient network analyzer E5071B, construct an automatic measurement system. I believe that most people are aware NI' s GPIB-based bus, you can realize automatic measurement, but NI' s program is too expensive, the use of MATLAB can greatly reduce costs. ccs between matlab and RTDX protocol-based data exchange, while matlab based on TCP/IP protocol and communication between the E5071B, the source described as follows: (1) RTDX_ok directory: matlab7.0 code, contains a GUI implementation with the interface and specific code, especially in one of implementation of the SCPI language to control the apparatus. (2) TMS320F2812 directory: contains ccs of c code, if not done RTDX application, then I think it was very instructive for you.)
- 2009-03-27 21:43:54下载
- 积分：1
-
revise-simulacion-3niveles-ba
simulation bad three level
- 2013-02-08 14:35:16下载
- 积分：1
