-
anjian
此程序为4*4矩阵键盘，键盘自身不带电源电阻，八个接线，在程序中进行需进行软件拉高拉低以便按键扫描。 应用单片机为MSP430F5529。(4* 4 matrix keyboard without power resistors MSP430F5529)
- 2014-07-04 16:25:28下载
- 积分：1
-
pinlv
频率相位测量的程序。实现相位差的测量与显示。(Frequency phase measurement process. Implementation phase of the measurement and display.)
- 2021-04-18 12:28:52下载
- 积分：1
-
Stepper-motor-acceleration
基于单片机和C语言的，步进电机加速减速匀速演示，希望方便大家(Based on SCM and C language, stepper motor acceleration and deceleration uniform presentation, I hope to facilitate)
- 2013-10-09 10:58:38下载
- 积分：1
-
ovl30u_vp1
此程序用于adina粘塑性材料的二次开发，仅仅针对二维。(
This procedure is used for the two development of ADINA viscoplastic materials, only for two-dimensional.
)
- 2016-08-11 21:28:52下载
- 积分：1
-
svpwm
DSP28335空间电压矢量调制SVPWM调制程序，浮点DSP编程(DSP28335 space vector modulation SVPWM modulation program)
- 2014-05-03 14:46:24下载
- 积分：1
-
main
7620摄像头采集程序（飞思卡尔128芯片）(7620 camera acquisition program (the Freescale 128 chip))
- 2012-11-24 16:41:44下载
- 积分：1
-
Si4432
简单的总结si4432的程序资料，非常地实用，简单。(Simple summary si4432 program information is very practical and simple.)
- 2012-07-31 20:03:42下载
- 积分：1
-
NTC_calculator
NTC热敏电阻计算器（B值、R25、指定温度、指定阻值均可计算，给定四个参数即可计算第五个参数）(NTC thermistors Calculator (B value, R25, specified temperature, the resistance can be specified calculation, four parameters can be calculated given the fifth parameter))
- 2016-02-20 13:18:42下载
- 积分：1
-
BattTestV2.0
一个通过USB->UART读取C8051F060的程序，实现曲线分析、放大、报表等，采用多线程。
驱动从www.silabs.com下载，要用NI的UI控件。完整版。(a USB-)
- 2007-01-21 13:10:10下载
- 积分：1
-
lcd1602C
xl系列单片机实验仪演示程序 LCD1602显示 步进电机控制器速度方向圈数可调 LCD1602显示 步进电机控制器速度方向圈数可调 K1－启动与停止步进电机运行 K2－设定步进电机运行圈数 （1-20圈） K3－设定步进电机转动方向 K4－设定步进电机运行速度 步进电机的转速控制分16档，数字越小，转速越快。 7.5度步进电机；周期7.5×4=30度，电机转动一圈需12个周期 资源：p1.0-p1.3接反向器74ls14，输出后接步进电机 p3.7接小喇叭提供按键音, p1.4-p1.7接端口按键：lcd1602插入实验仪(xl Series Singlechip Experiment LCD1602 demo program shows the direction of stepper motor speed controller circle shows the number of adjustable LCD1602 direction stepper motor controller lap speed of a few adjustable K1-start and stop the stepper motor running K2-setting step motor running a few laps (1-20 laps) K3-set stepper motor rotation direction of K4-setting speed of stepper motor stepper motor speed control minutes 16 stalls, the number of smaller, faster the speed. 7.5 degree stepper motor cycle of 7.5 × 4 = 30 degrees, rotating electric lap 12 cycles required resources: p1.0-p1.3 then reverse browser 74ls14, followed by stepper motor output p3.7 then provide a small speaker key tone, p1.4-p1.7 port access keys: lcd1602 insert Tester)
- 2008-12-19 10:42:22下载
- 积分：1
