-
threshold_segmentation
说明： 用阈值迭代分割算法对图像进行二值化（matlab）(Iterative segmentation algorithm with the threshold value of the image binarization (matlab))
- 2009-08-27 10:38:53下载
- 积分：1
-
msequence
利用线性反馈移位寄存器产生周期为2^n-1，任意长度的m序列(The linear feedback shift register cycle is 2 ^ n-1, any length m-sequences)
- 2012-05-18 21:58:06下载
- 积分：1
-
GetMousePointer
用matlab程序编写的一个捕捉鼠标坐标的小程序，用来参考。(Matlab programmers use to capture the mouse coordinates of a small program used to refer to.)
- 2009-05-06 18:42:54下载
- 积分：1
-
KNN11
说明： matlab有关K近邻分类算法，很不错，看看(matlab knn )
- 2011-03-17 16:50:50下载
- 积分：1
-
target-tracking
考虑两辆车在道路上同向行驶，在O-16s时，两车均保持匀速直线运动，由安装在后车上的车载毫米波雷达检测出与前车的距离为150m，相对速度为-3m/s，方位角 。在16-20s时，前车向右偏转，与后车的相对角加速度为 。后车加速，与前车的纵向相对加速度为 。雷达的扫描周期为T=0.1s，系统噪声为 ， 。量测误差为 。(Consider the two cars traveling the same direction on the road, in the O-16s, the two vehicles are kept uniform linear motion, installed in the vehicle after the car millimeter wave radar to detect the distance of the vehicle in front 150m, the relative speed- 3m/s, Azimuth. In the 16-20s, the first car to the right deflection, and the relative angular acceleration after the car is. After the vehicle acceleration, relative to the vehicle in front of the vertical acceleration. Radar scan period T = 0.1s, the system noise. Measurement error.)
- 2021-04-07 21:29:01下载
- 积分：1
-
MATLAB-numerical-computation-cases
《MATLAB数值计算案例分析》一书的源程序，供大家学习。(《MATLAB numerical computation cases analysis》 s programs.)
- 2013-03-11 19:47:11下载
- 积分：1
-
Myoelectric_control-system
一篇很好的关于肌电信号的综述性文章，希望对大家有用(A good overview of the EMG signal on the article, I hope to be useful)
- 2011-10-22 11:11:00下载
- 积分：1
-
MATLAB
关于通信系统的matlab源码,介绍的是OFDM的相关原理(About communication systems matlab source)
- 2014-01-01 21:32:30下载
- 积分：1
-
Voltage sags are one of the main problems
Voltage sags are one of the main problems in transmission
and distribution grids with high penetration of distributed
generation. This paper proposes a voltage support control scheme
for grid-connected power sources under voltage sags. The control
is based on the injection of reactive current with a variable ratio between
positive and negative sequences. The controller determines,
also, the amount of reactive power needed to restore the dropped
voltage magnitudes to new reference values confined within the
continuous operation limits required in grid codes. These reference
values are chosen in order to guarantee low current injection
when fulfilling the voltage support objective. Selected experimental
results are reported in order to validate the effectiveness of the
proposed control.
- 2014-04-17 21:22:47下载
- 积分：1
-
gui
I have uploaded complete GUI code for Aircraft A320 control
- 2016-04-11 01:28:45下载
- 积分：1
