登录
首页 » matlab » optimization

optimization

于 2012-10-04 发布 文件大小:4947KB
0 227
下载积分: 1 下载次数: 15

代码说明:

  最优化计算方法常用程序汇编,参考价值很大(failed to translate)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • robot-9.8
    Robot Toolbox for simulation Robotic manipulators and Design Controller for robots
    2013-07-17 01:20:04下载
    积分:1
  • Vicsek模型
    多个体系统的集体行为是复杂系统研究的重要切入点, 而Vicsek 模型是 研究多个体系统的一个基本模型, 它具备了复杂系统的一些关键特征, 如动态行 为、局部相互作用和变化的邻居关系等.(Collective behavior of multi agent system is an important entry point for complex system research, and Vicsek model is a basic model of multi agent system, which has some key features of complex system, such as dynamic behavior, local interaction and changing neighbor relations)
    2017-11-27 17:28:22下载
    积分:1
  • 6807EF2Ed01
    matlab probability simple simulation
    2012-04-30 20:39:07下载
    积分:1
  • LabelMeToolbox
    LaberMe Toolbox. Toolbox for using labelme images.
    2011-01-05 21:50:27下载
    积分:1
  • nurbs_toolbox
    non linear B spline curve fitting
    2012-07-04 14:19:37下载
    积分:1
  • ESPRIT-MATLAB
    本程序是利用ESPRIT 算法实现波达方向的估计,程序能直接运行,有一定的参考价值。。(This program is the use of ESPRIT DOA estimation algorithm, the program can be run directly, there is a certain reference value. .)
    2014-12-26 10:54:06下载
    积分:1
  • 项目4
    说明:  任务:设计一个4×2.5Gbit/s 长距离光纤传输系统,并利用OptiSystem 仿真验证。 要求: 1.采用波分复用技术,波长设置以100GHz 为间隔,频率分别为193.1THz、193.2THz、193.3THz、193.4THz,每个波长传输速率为2.5Gbit/s(NRZ),传输距离为300km。采用常规光纤,光纤损耗系数为0.25dB/km。 2.单通道光发送机最大输出功率为0dBm,光接收机的接收光功率不低于-26dBm,过载点为-10dBm。 3.可以采用EDFA 作为线路放大器,其中EDFA 的输入功率限制在-18~2dBm,最大输出功率20dBm,增益范围为13~25dB,噪声指数4.0dB。(Task: Design a 4 x 2.5 Gbit/s long-distance optical fiber transmission system, and use OptiSystem simulation to verify. Requirement: 1. Using wavelength division multiplexing technology, the wavelength is set at 100GHz intervals, with frequencies of 193.1 THz, 193.2 THz, 193.3 THz and 193.4 THz, respectively. The transmission rate of each wavelength is 2.5 Gbit/s (NRZ), and the transmission distance is 300 km. The loss coefficient of conventional optical fibers is 0.25dB/km. 2. The maximum output power of a single-channel optical transmitter is 0 dBm, and the receiving power of an optical receiver is not less than -26 dBm, and the overload point is -10 dBm. 3. EDFA can be used as line amplifier, where the input power of EDFA is limited to - 18-2dBm, the maximum output power is 20dBm, the gain range is 13-25dB, and the noise index is 4.0dB.)
    2019-05-13 09:39:41下载
    积分:1
  • srtp21
    我做了这样一个电子菜单,除普通菜单功能外,增加了控制饮食的功能。因此称作“健康电子菜单”。 (I had such an electronic menu, in addition to ordinary menu functions, an increase of the function of diet. So called " health e-menu." )
    2009-05-21 15:50:19下载
    积分:1
  • MyRD
    率失真曲线的生成代码,自定义信源结构及迭代误差。附带实验说明(Rate-distortion curve of the generated code, custom source structure and iterative error. Help with experiment)
    2011-01-04 19:43:18下载
    积分:1
  • fuel-cell1
    simulation of fuel cell -part2
    2013-07-29 15:56:18下载
    积分:1
  • 696516资源总数
  • 106627会员总数
  • 16今日下载