登录
首页 » matlab » toolbox_graph

toolbox_graph

于 2015-02-07 发布 文件大小:2919KB
0 328
下载积分: 1 下载次数: 4

代码说明:

  matlab code for Toolbox Graph

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • signpost_recognize
    Matlab编写的路标识别程序。能够对路标进行分类和识别,即使雾化,干扰严重,仍能较准确的判断。(Signs written in Matlab identification procedures. Able to classify and identify road signs, even atomization, serious interference, still a more accurate judgments.)
    2010-08-08 08:33:35下载
    积分:1
  • cucaoji
    粗糙集结合遗传算法纠结是集中的一个问题,附论文和论文中的代码。(Tangled rough sets and genetic algorithm is a problem concentrated, with papers and papers code.)
    2014-11-18 20:46:22下载
    积分:1
  • AO_Basic
    关于短路计算的一些源程序,同时是有关matlab的源程序(Short-circuit calculations on some of the matlab source code is also optimized source)
    2011-11-28 10:53:33下载
    积分:1
  • 双移线仿真
    双移线仿真,车辆稳定性控制跟踪曲率,工程应用(Double line simulation and vehicle stability control track curvature)
    2021-04-08 14:59:01下载
    积分:1
  • read_letter
    this is a code in matlab for character recognition depending on correlation
    2009-05-24 16:45:31下载
    积分:1
  • 87361021matlabworkElectricalpowerandvoltagecalcula
    Electrical power and voltage calculate
    2008-07-08 19:33:37下载
    积分:1
  • 16QAM-OFDM
    说明:  基于16QAM调制解调的OFDM信道估计,计算了不同信噪比下的误码性能曲线,并画出了图。(Comb based on the OFDM pilot channel estimation, calculation of the BER performance under different signal to noise ratio curve, and draw the map.)
    2010-04-29 09:30:01下载
    积分:1
  • cylinder2
    [X,Y,Z]=cylinder2(x,y,z,r,N,o) 向量X,Y,Z轴定义圆柱面中心线 和矢量r定义圆柱面半径,并已 为的x,y,z的长度相同 N是周围围点的数量。默认值 为N= 100。 Ø 定义了矩阵圆柱generatix(圆圈)椭圆 表面。其内容以0和1之间的值,并适用于 小学和中学的母线轴。值的defeault Ø =的(长(x),2)。 矩阵X,Y,Z轴确定圆柱面,冲浪(的X,Y,Z)的显示器 圆柱面。( [X,Y,Z]=cylinder2(x,y,z,r,N,o) Vectors x, y, z define the central line of cylindrical surface and vector r defines the radius of cylindrical surface, and has the same length as x, y, z. N is the number of points around the circumference. The default value is N = 100. Matrix o defines ovality of the generatix (circle) of cylindrical surface. Its elements take values between 0 and 1 and apply to the primary and secondary axis of generatrix. The defeault values are o=ones(length(x),2). Matrices X, Y, Z define the cylindrical surface, surf(X,Y,Z) displays the cylindrical surface. )
    2011-05-15 10:56:33下载
    积分:1
  • QPSK_sfun
    QPSK Modulation and Demodulation with AWGN , Performance comparision against on BER / EB/NO ratio.
    2012-05-03 18:23:39下载
    积分:1
  • matlab1
    了解单频激光干涉仪的非线性误差,使用matlab软件工具对提出的非线性误差修正方法进行验证,对干涉信号中的直流分量偏差对测量的影响进行分析。(Learn nonlinearity error single frequency laser interferometer using matlab software tools for the proposed non-linear error correction method for verification of the DC component of the interference signal on the measurement of the deviation analysis.)
    2014-11-12 22:44:26下载
    积分:1
  • 696518资源总数
  • 106148会员总数
  • 10今日下载