登录
首页 » matlab » gongzhenok

gongzhenok

于 2020-11-01 发布 文件大小:30KB
0 211
下载积分: 1 下载次数: 209

代码说明:

  产生随机共振现象的输入输出信噪比曲线,参数可以修改,不过不要乱改动哦,不然振动不起来了。(Stochastic resonance phenomenon generated input and output signal to noise ratio curve.)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • BOD_TB24
    Digital Amplitude Optimum (BOD) for discontinuous control
    2010-05-20 01:34:24下载
    积分:1
  • 4FSK_m
    4FSK正交调制解调 其中有升余弦成型滤波,梳形内插。画出误码率曲线(4FSK modulation and demodulation with raised cosine shaping filter, comb shape interpolation. Draw the curve of error rate)
    2020-07-04 09:20:02下载
    积分:1
  • 3D-PLOT-USING-MATLAB-IN-PSCAD
    3D PLOT USING MATLAB IN PSCAD WARNING * This case only works if you use the Compaq/Intel Fortran Compiler. A T_D_PLOT component. It provides the interface to a MATLAB function t_d_plot . It is a user-defined function and the m-file T_D_plot.m contains its definition. This component plots a 3-dimensional curve. Input: X, Y and Z values of the point to be plot Output: a dummy output of value zero Parameters of T_D_PLOT component.
    2014-01-04 09:39:02下载
    积分:1
  • OFDM-basedWirelessBroadBandSystemSimulator
    基于OFDM的无线宽带系统仿真It contains mainly two parts, i.e. link-level simulator and system-level simulator. Link-level simulator focus on a single-cell single-user scenario, where signal is transmitted from tx, and estimated at rx. Comparing the difference in tx/rx signal, the error rate can be found out. The output of the link-level simulator is the BLER/BER vs. SNR mapping table, that can be used for the system-level simulation. System-level simulator focus on a multi-cell multi-user scenario. For the sake of simplicity, it takes the mapping table aquired in the link-level simulation, measure the actural SNR, and finds the corresponding error rate.(OFDM-based wireless broadband system simulation It contains mainly two parts, ie link-level simulator and system-level simulator.Link-level simulator focus on a single-cell single-user scenario, where signal is transmitted from tx, and estimated at rx . Comparing the difference in tx/rx signal, the error rate can be found out. The output of the link-level simulator is the BLER/BER vs. SNR mapping table, that can be used for the system-level simulation.System- level simulator focus on a multi-cell multi-user scenario. For the sake of simplicity, it takes the mapping table aquired in the link-level simulation, measure the actural SNR, and finds the corresponding error rate.)
    2008-01-05 00:08:29下载
    积分:1
  • thesis2k
    PAPERS ON DYNAMIC VOLTAGE RESTORER
    2011-02-10 16:52:49下载
    积分:1
  • power_regulzero
    power_regulzero,功率电子领域matlab仿真文件,已经验证过,程序运行正常(power_regulzero,Power electronics field matlab simulation file, has already been verified, the normal operating procedures)
    2013-07-14 12:29:43下载
    积分:1
  • new-example-of-statistics
    一些较新的数据统计与分析方面的例子。含有多个有价值的MATLAB例子。(new examples of statistics and analysis)
    2012-05-23 17:46:30下载
    积分:1
  • denoise_waverec-(2)
    计算损伤结构前后的响应,对已结构的分析具有很好的效果(After calculating the response of the structure damage, the structure analysis of a good effect)
    2013-10-26 09:49:04下载
    积分:1
  • pcmcode
    律u律pcm编码 若输入A律PCM编码器的正弦信号为x(t)=sin(1600πt),采样序列为x(n)=sin(0.2πn),n=0,1,2,…,10,将其进行PCM编码,求出编码器的输出码组序列y(n)。 要求:1) 直接采用A律扩展器函数求解上述问题。 2)使用13折线法近似A律PCM 求解上述问题。 3)计算量化误差。(Law a law pcm coding If the input A-law PCM encoder is sinusoidal signal x (t) = sin (1600πt), for the sample sequence x (n) = sin (0.2πn), n = 0,1,2, ..., 10, it will be PCM coding to obtain the coded output code group sequence y (n). Requirements: 1) directly A-law expander function to solve the above problems. 2) using a 13 fold line approximation A-law PCM to solve the above problems. 3) calculating the quantization error.)
    2016-04-06 19:30:12下载
    积分:1
  • cesaraffine
    Cryptage et decryptage Cesaraffine
    2014-12-06 01:12:14下载
    积分:1
  • 696516资源总数
  • 106409会员总数
  • 8今日下载