-
jpegcompresion
description on Matlab of JEPG compression
- 2010-09-13 02:51:18下载
- 积分：1
-
mutibodyMatlab
用于计算多体系统动力学的程序,可用于多体系统动力学的计算和仿镇,也可用于机器人的设计和计算(used in the calculation of multi-body system dynamics procedure can be used for multi-body system dynamics calculations and imitate town, Robots can also be used for the design and calculation)
- 2021-04-06 09:49:03下载
- 积分：1
-
chap10
matlab图像处理实例详解chap10——图像压缩编码(matlab image processing examples explain chap10- Image Coding)
- 2013-12-16 15:52:41下载
- 积分：1
-
TwoR
this program shows the dynamical equation
- 2015-02-27 06:25:41下载
- 积分：1
-
201003tecplot
说明： 简介卫星姿态控制系统的模型，并针对该模型分析故障发生的特点，故
障诊断的难点，以及可能发生故障的部位和故障的类型，给出故障检测的方法。(Introduction of satellite attitude control system model and the model for the analysis of the characteristics of faults, fault diagnosis of the difficulties, and possible failure location and fault type, fault detection methods are given.)
- 2010-03-23 22:02:43下载
- 积分：1
-
CUM2EST
求信号二阶矩的matlab源程序，在基于二阶统计量的信号处理中有重要作用 (second-order cumulant)
- 2012-04-19 14:28:11下载
- 积分：1
-
matlab--some-nice-programs
Matlab画平滑曲线的两种方法（ 拟合或插值后再用plot即可）
自然状态下，用plot画的是折线，而不是平滑曲线。有两种方法可以画平滑曲线，第一种是拟合的方法，第二种是用spcrv，其实原理应该都一样就是插值。下面是源程序。(You can then use the plot)
Natural state, with the plot is a line drawing, instead of a smooth curve. There are two ways to draw a smooth curve, the first one is the fitting method, and the second is to use spcrv, in fact, the same principle should be that the interpolation. Here is the source.)
- 2015-03-23 16:35:58下载
- 积分：1
-
雷达信号处理基本流程
去斜处理（宽带的匹配滤波）Stretch方法是针对线性调频信号而提出的， 其方法是将输入信号与参考信号 （经适当延迟的本振信号， 延迟量通常由窄带信号测距结果估计出） 混频 ，则每一个散射点就对应一个混频后的单频分量，对混频输出的信号进行 DFT 处理 ，即可获得目标的距离像，对参考信号的要求是应具有与输入信号相同的调频斜率。(dechirp matched filter
Stretch method is proposed for linear frequency modulation signal. It mixes the input signal with the reference signal (local oscillator signal with appropriate delay, the delay is usually estimated from the result of narrowband signal ranging). Then each scattering point corresponds to a single frequency component after mixing, and DFT is performed on the mixed-frequency output signal. The range profile of the target can be obtained by processing, and the reference signal is required to have the same frequency modulation slope as the input signal.)
- 2018-10-31 20:07:27下载
- 积分：1
-
Bez_Sq_Err
The classic method of calculating GLCM texture, based on matlab platformThe classic method of calculating GLCM texture, based on matlab platform
- 2013-04-30 16:12:54下载
- 积分：1
-
NCSR
这是基于CSR算法在非局部环境的扩充表示，并应用在去噪上(This algorithm is based on CSR in the expansion of non-representation of the local environment, and apply the de-noising)
- 2013-12-25 10:14:05下载
- 积分：1
