登录
首页 » Visual C++ » 12864

12864

于 2013-12-27 发布 文件大小:20KB
0 243
下载积分: 1 下载次数: 2

代码说明:

  51单片机中的LCD12864显示,用的是C语言,为KEIL程序包。(51 microcontroller in LCD12864 display)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • zhongjile
    通过51单片机设计一个电子时钟,精确到秒,可以通过按键调节时间(By 51 microcontroller design an electronic clock, accurate to seconds, you can adjust the time by pressing a button)
    2013-11-14 09:56:13下载
    积分:1
  • ICcardWR
    使用读卡器实现了为个人化的IC卡数据读写(Achieved using the reader for personal IC card data read and write)
    2007-12-04 23:00:55下载
    积分:1
  • EEPROM
    本系统是基于mega16的EEPROM的读写,程序可靠!(The system is based on the mega16 the EEPROM read and write, program and reliable!)
    2011-07-08 18:14:03下载
    积分:1
  • JN-AN-1229
    说明:  zigbee document upload 23/7/2019
    2020-06-21 18:00:02下载
    积分:1
  • Key
    msp430f149按键程序,非常完整,带中断,输入,输出(msp430f149 key procedures)
    2014-06-13 15:06:31下载
    积分:1
  • Responder
    抢答器论文及其proteus仿真资料 单片机C51程序(Responder papers and proteus simulation data C51 MCU program)
    2016-12-22 16:55:12下载
    积分:1
  • 1602QG
    F340 LCD1602 模块程序 (F340 LCD1602 module program)
    2011-05-12 23:08:46下载
    积分:1
  • QuangBao
    it is program for led matrix
    2012-01-09 17:49:50下载
    积分:1
  • CT
    说明:  双路输出控制器”具有信号输出时间设定、 输出信号占空比调整、 当前输出通道及时 间显示、系统工作参数存储、串口通讯及 LED 指示等功能。 “双路输出控制器”通过串口完 成信号输出时间设定功能;通过 EEPROM 完成系统工作参数存储功能;通过按键完成输出通 道切换、 输出信号占空比调整及停止信号输出功能; 系统硬件电路主要由 MCU 控制单元、独 立按键、 LCD 显示单元、 串口通讯单元、 EEPROM 数据存储单元和 LED 指示单元组成(Dual output controller has the signal output time setting, adjust the duty cycle of the output signal, the current output channel in time Between display, system operating parameters are stored, serial communications and LED indicator. Dual Output Controller through serial END A signal output time setting function complete system operating parameters via EEPROM memory function complete output pass through the key Channel switching, adjust the duty cycle of the output signal and the stop signal output function the system hardware circuit is mainly controlled by the MCU unit, alone Li buttons, LCD display unit, serial communication unit, EEPROM data storage unit and LED indication units)
    2015-03-10 20:14:34下载
    积分:1
  • 11
    说明:  利用定时/计数器T0从P1.0输出周期为1s的方波,让发光二极管以1HZ闪烁,设晶振频率为12MHz(The use of timer/counter T0 from P1.0 output cycle square wave 1s, so that the light-emitting diodes 1HZ blinking, set the crystal frequency is 12MHz)
    2014-05-27 14:30:43下载
    积分:1
  • 696516资源总数
  • 106633会员总数
  • 4今日下载