登录
首页 » matlab » RN

RN

于 2015-06-21 发布 文件大小:3KB
0 124
下载积分: 1 下载次数: 0

代码说明:

说明:  classification with neural network mono and multi layer

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • FastNxNSolver
    fastsolving linear equation
    2009-02-16 17:23:14下载
    积分:1
  • NORMALIZED_CUT
    Normalized Cut for image segmentation
    2010-11-04 12:50:02下载
    积分:1
  • SimPowerSystems
    利用matlab/simulink进行电气系统仿真。提供说明与示例。(Using matlab/simulink simulation of the electrical system. Provides instructions and examples.)
    2010-11-20 22:35:50下载
    积分:1
  • DIPUM_toolbox_m-file
    Digital Image Processing Using Matlab Additional Material
    2011-05-27 22:29:52下载
    积分:1
  • 45666027backstepping-Control-track-
    说明:  通过设计模糊PID控制器,实现对直线、圆轨迹较为精准的跟踪(By designing a fuzzy PID controller, the accurate tracking of straight and circular trajectories can be achieved.)
    2019-09-26 16:03:47下载
    积分:1
  • GenerateCAcode3.m
    基于MATLAB环境下的关于GPS接收的一部分(GPS receive signal)
    2010-05-17 17:56:23下载
    积分:1
  • bottom_up_segmentation
    这是TD算法的逆过程,首先将时间序列,划分为相邻点的短序列,当然此时的拟合误差为0,因为第一点和第二点的连线,原始点都落在线段上。将相邻两个线段连接起来,此时每条线段包含三个原始点,计算中间那个点的拟合误差。这样,所有这些三个点的线段中的中间点的拟合误差计算出来后,找出误差最小且误差小于阀值R的分段,作为第一条包含三个点的线段。 在上面的基础上,第一条分段同样的和相邻线段连接,然后计算每一条分段的拟合误差,再找出误差最小且小于阀值R的分段,作为第二个分段。依次方式循环,直到所有分段的拟合误差都小于阀值R,分段结束。 (This is the reverse process of TD algorithm, the first time series is divided into short sequences adjacent dots, of course fitting error is zero at this time, because the first and second points of connection, the original point fall line on. The two adjacent segments are connected, then each segment contains three original point, the intermediate fitting error calculated that point. Thus, after all these segments fitting error of three points in the intermediate point calculated to find the minimum error and the error is less than the threshold R segment, as the first line contains three points. Based on the above, the first segment and the adjacent line segment connecting the same, and then calculate a fitting error for each segment, and then find the smallest error and less than the threshold R segment, as the second segment . Followed by a cyclic manner until all segments fitting error is less than the threshold R, segment ends.)
    2021-03-20 16:29:18下载
    积分:1
  • 粗糙度matlab
    计算一维和二维表面粗糙度Ra,根据需要自行选择。(Calculate one and two dimensional surface roughness Ra, according to the needs of your choice.)
    2017-08-01 21:59:44下载
    积分:1
  • kmeans
    this code can segment class using kmeans
    2009-03-04 17:22:16下载
    积分:1
  • ICSMATLAB_28-02-06
    cell migration resource imaging icsmatlab
    2009-05-18 00:33:38下载
    积分:1
  • 696518资源总数
  • 105877会员总数
  • 14今日下载