-
power_PSS
说明： matlab仿真建模，用于电力系统可靠性分析，建立的2区，四机模型，用于电力系统可靠性分析与规划、潮流计算(Matlab simulation modeling, used for power system reliability analysis, the establishment of a 2-zone, four-machine model, used for power system reliability analysis and planning, power flow calculation)
- 2020-06-19 11:45:12下载
- 积分：1
-
ModelB
说明： 利用相场方法，计算枝晶生长，标记为相场动力学模型B。(Dendrite growth was calculated by phase field method and marked as phase field dynamics model B.)
- 2020-06-24 02:40:02下载
- 积分：1
-
matlab 拓扑优化
包含多种MATLAB拓扑优化程序，运用SIMP、渐进结构优化方法实现结构的拓扑优化。(A variety of MATLAB topological optimization procedures are included, and the topology optimization of the structure is realized by using SIMP and progressive structural optimization.)
- 2021-04-28 11:18:44下载
- 积分：1
-
利用相场晶体模型 PFC_alloy
利用相场晶体模型，计算枝晶生长等。标记为相场晶体模型。(Dendrite growth is calculated by phase field crystal model. It is labeled as phase field crystal model.)
- 2020-09-25 16:17:47下载
- 积分：1
-
wind-direction
提取中尺度WRF模式指定高度处的风向时程(To extract time series of wind direction at specific height)
- 2020-10-26 10:29:59下载
- 积分：1
-
通过matlab实现地震剖面、单炮记录、道集等地震数据的成像和成图plotseis
说明： 通过matlab实现地震剖面、单炮记录、道集等地震数据的成像和成图(Imaging and mapping of seismic data such as seismic profile, single shot record and trace set by MATLAB)
- 2020-05-28 20:47:43下载
- 积分：1
-
三极管放大电路设计
说明： 三极管放大实验电路，包括固定偏置/分压偏置，需要根据一些参数确定所选用的电阻值，使得三极管工作在放大状态。本程序将电路设计设计成GUI模式，界面上只需要输入电路设计所需参数，根据相关理论推导，给出相关参数的理论值（放大倍数、输入电阻、输出电阻等），指导实验电路搭建。软件搭建在matlab gui上，方便使用
若干参数说明
beta：三极管放大倍数
Ic：集电极电流
Uce：期望CE间电压
UeCof：Re电阻上点电压与Ucc电压比值，一般0.1-0.2
IbCof：Ib上电流与流过Rb1、Rb2电流的比值，一般0.1
ShuntCe：是否有旁路电容(The experiment circuit of triode amplification, including fixed bias / partial voltage bias, needs to determine the selected resistance value according to some parameters to make the triode work in the amplification state. In this program, the circuit design is designed into GUI mode. Only the parameters needed for circuit design are needed on the interface. According to the relevant theoretical derivation, the theoretical values of the relevant parameters (magnification, input resistance, output resistance, etc.) are given to guide the construction of experimental circuit. The software is built on Matlab GUI, easy to use)
- 2020-04-29 15:11:59下载
- 积分：1
-
不同边界条件下均匀直梁固有频率计算软件源代码
说明： 本软件用于计算不同边界条件下均匀直梁横向、纵向前三阶固有频率。(The software is used to calculate the first three natural frequencies of the transverse and longitudinal direction of a uniform straight beam under different boundary conditions.)
- 2019-12-13 18:34:06下载
- 积分：1
-
lliangdianfa
说明： 通过两点法 计算水波的反射系数 海洋工程领域实用代码(The reflection coefficient calculation by two points method. Useful code for ocean engineering.)
- 2021-04-06 10:19:02下载
- 积分：1
-
c4797725
说明： 滑动轴承弹流润滑程序，压力，油墨厚度等等，十分方便(The elastohydrodynamic lubrication procedure, pressure, ink thickness and so on are very convenient)
- 2020-05-16 14:54:03下载
- 积分：1
