-
子空间辨识（ABCD）
说明： 建立基于子空间辨识的PEMFC电特性状态空间模型。(A state space model of PEMFC electrical characteristics based on subspace identification is established.)
- 2021-04-28 09:08:44下载
- 积分：1
-
boost
说明： 状态空间Boost建模，用增广系统进行状态反馈控制恒压(The state space boost model is built, and the augmented system is used to control the constant voltage)
- 2020-12-28 14:44:21下载
- 积分：1
-
_SAR_ADC
说明： matlab对sar_adc相关数据的建模(Matlab for SAR_ Modeling of ADC related data)
- 2021-02-01 17:50:00下载
- 积分：1
-
kong
说明： 在 Carsim 中分别搭建好前车与后车的车辆纵向动力学
模型。雷达系统将探测到的后车信息和前车信息传递给行车
间距控制系统，此控制系统根据安全距离模型计算出后车车
辆期望加速度，此期望加速度经过 PID 控制器调节后，输入
给车辆动力学系统，车辆动力学系统基于此加速度输出期望
的制动压力和节气门开度，并将此值传给制动及节气门控制
系统，此系统输出相应的制动力及节气门开度给后车动力学
系统，进行制动及加速控制。(The vehicle longitudinal dynamics of the front car and the rear car were built respectively in Carsim
Model.The radar system transmits the information of the vehicle behind and the vehicle in front to the vehicle
Spacing control system, this control system according to the safe distance model to calculate the rear car
Vehicle expected acceleration, the expected acceleration after PID controller adjustment, input
Given to the vehicle dynamics system, the vehicle dynamics system is based on this acceleration output expectation
Brake pressure and throttle opening, and pass this value to brake and throttle control
System, which outputs the corresponding braking force and throttle opening to the rear car dynamics
System for braking and acceleration control.)
- 2021-03-19 11:09:19下载
- 积分：1
-
ABAQUS_UMAT的开发
umat基础知识教学，适合刚接触UMAT的新手做参考(UMAT basic knowledge teaching, suitable for beginners)
- 2018-12-28 17:00:40下载
- 积分：1
-
three_level
该模型用于电力电子三电平逆变器的仿真，结构完整，功能齐全，既可以与电机等其他设备配合使用，也可以单独使用。(simulink model for 3-phase inverter)
- 2017-08-08 10:09:57下载
- 积分：1
-
vector
说明： 电机矢量控制仿真（svpwm方法）实测有效 包括坐标变换(vector control The simulation of motor vector control (SVPWM) includes coordinate transformation)
- 2021-02-08 20:09:38下载
- 积分：1
-
无人机模型_GUI
说明： 无人机模型，GUI界面，模拟飞机飞行过程(UAV model
GUI interface
Simulation of aircraft flight process)
- 2020-10-29 17:22:20下载
- 积分：1
-
usermat_CDM
These composite materials generally exhibit brittle damage behavior. The anisotropy in the
material and different kinds of failure mechanisms make it difficult to accurately
characterize the behavior of composite materials. The present work aims to verify and
apply the Puck Failure Criteria using the commercially available finite element package
ANSYS by writing a user-material subroutine in FORTRAN. The model is implemented
with different post failure degradation schemes EWM/CSE.
- 2019-05-01 00:48:50下载
- 积分：1
-
S参数反演程序
利用S参数，即S11和S21反演介质的有效介电常数和有效磁导率(Inversion of effective permittivity and permeability of dielectrics using S parameters, i.e. S11 and S21)
- 2021-01-26 17:18:41下载
- 积分：1
