-
hongwai-lcd.c
基于51单片机的 红外+LCD+继电器C程序显示
实现的功能较多，比较适合初学的人。(Based on 51 single-chip infrared+LCD+ relay C program display of more functions, more suitable for beginners person.)
- 2013-08-17 11:14:48下载
- 积分：1
-
dianzheng
点阵程序
4片16*16点阵显示程序，可以正显，反显，左右移动。(Dot-matrix program 4 16* 16 dot matrix display program, you can now significantly, anti-marked, about mobile.)
- 2008-08-12 13:14:24下载
- 积分：1
-
PV
说明： 光伏逆变器的双闭环控制仿真原理图 dc-dc采用mppt跟中(The double closed loop control simulation diagram of photovoltaic inverter)
- 2013-11-09 14:57:46下载
- 积分：1
-
智能车终端RAM代码
说明： 小车控制，蓝牙通信 温湿度传感器驱动 pm2.5传感器驱动(Car Control, Bluetooth Communication Temperature and Humidity Sensor Drive PM2.5 Sensor Drive)
- 2020-06-22 16:40:02下载
- 积分：1
-
双向DCDC
本设计以双向半桥电路为主拓扑结构，以单片机最小系统板为控制核心，协调各个模块工作以实现题设功能。电路分为主电路拓扑模块、控制模块、PWM控制信号驱动模块、辅助电源模块、电压电流采样模块。(This design takes the two-way half bridge circuit as the main topology, takes the smallest system board of the single chip microcomputer as the control core, and coordinates the work of each module in order to realize the design function. The circuit is divided into main circuit topology module, control module, PWM control signal driving module, auxiliary power module, voltage and current sampling module.)
- 2018-06-24 16:43:55下载
- 积分：1
-
RGB_Colour1618447212003
RGB Colour Wheel for Visual Basic
- 2016-01-28 22:22:18下载
- 积分：1
-
51-bread-furnace-program
一个拷面包炉的的汇编程式，用8051 MCU，有键盘控制等...(A bread furnace program for 8051 MCU)
- 2011-09-18 20:31:39下载
- 积分：1
-
Button_led_flashing
在IAR环境下编写msp430f4152源码，通过单片机开发板上的按键来控制发光二极管的亮灭。(In the IAR environment to prepare msp430f4152 source, SCM development board buttons to control LED light off.)
- 2013-09-04 11:00:52下载
- 积分：1
-
Msp430-based-oscilloscope
基于msp430g2553的简易示波器
无需外设.超低功耗
诺基亚5513显示
(Msp430 based oscilloscope)
- 2014-01-12 12:16:42下载
- 积分：1
-
LCD
用C语言编写STM32嵌入式程序，设计一个万年历系统，并用HX1230屏显示相关的时间信息。
基本要求：
1.C语言程序要求是模块化设计。
2.该万年历要求能显示时间（时、分、秒）、年月日及闹钟定时时间（分、秒）。
3.该系统由2-3个按键可调整显示的时间、年月日及闹钟定时时间，具体各个按键功能及编程方式自定。
4.该闹钟可以定时时间到，LED将发出提示闪光，且持续30s。
5.HX1230屏能驱动显示。
6.定时时间可被打断，即打断后恢复时继续计时。
7.设置闹钟报警功能；
8.利用STM32自带的温度传感器功能，使系统能显示当前环境温度值。(STM32 embedded program is written in C language, a calendar system is designed, and relevant time information is displayed on HX1230 screen.
Basic requirements:
1. The requirement of C language program is modular design.
The calendar requires that time (hours, minutes, seconds), year, month, day and alarm clock timing time (minutes, seconds) be displayed.
3. The system can adjust the display time, year, month, day and alarm clock timing time by 2-3 keys, and the function and programming mode of each key are self-determined.
4. The alarm clock can be scheduled to arrive, and the LED will give a prompt to flash, and lasts for 30 seconds.
5. HX1230 screen can drive display.
6. Timing time can be interrupted, i.e. when the interruption is resumed, the timing will continue.
7. Setting alarm function of alarm clock;
8. Using the temperature sensor function of STM32, the system can display the current environmental temperature)
- 2020-06-25 05:00:02下载
- 积分：1
