登录
首页 » matlab » chap2-10

chap2-10

于 2009-10-11 发布 文件大小:184KB
0 184
下载积分: 1 下载次数: 342

代码说明:

  滑模变结构控制MATLAB仿真一书中,2到10章节的所有程序(MATLAB simulation of sliding mode variable structure control of a book, chapters 2 to 10 all of the programs)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • rls
    递推遗忘因子最小二乘 recursive forgotten factor ls(recursive forgotten factor ls)
    2010-03-08 10:25:44下载
    积分:1
  • vehicle-sub-system
    用于蒙特卡洛monte calro仿真方法的模拟(For the Monte Carlo simulation method simulation monte calro)
    2013-09-09 08:54:28下载
    积分:1
  • cyclic2_am
    AM信号的循环谱的matlab代码实现,初学者适合 (The AM signal of the cyclic spectrum of matlab code, suitable for beginners )
    2013-10-25 12:05:27下载
    积分:1
  • AICandMDL
    经典的信息论准则估计信号源个数。 使用空间谱估计理论,模拟发射信号由天线阵列接受采样。经过AIC和MDL两种算法,估计出采样序列中信号的个数,所加噪声是白噪声。(Classical information theory for sources number estimation. It s spatial spectrum estimation theory. it analogs transmission signal from the antenna array . It uses two algorithms“ AIC and MDL ”to estimate the number of sampled signal sequence. the added noise is white noise.)
    2021-03-25 11:39:14下载
    积分:1
  • GCC
    广义互相关函数来确定两个信号的时延差,时延定位相关程序(Generalized cross-correlation function to determine the time delay difference between the two signals, the delay positioning procedures)
    2020-10-30 11:09:56下载
    积分:1
  • hangshehoufangjiaohui
    应用于航空摄影测量竖直摄影模型的空间后方交会,用迭代的方法求解,摄像机的6个外方位元素(Measurement of vertical aerial photography used photographic model space resection, using an iterative method for solving the camera of the six exterior orientation elements)
    2010-01-13 19:00:16下载
    积分:1
  • fuzzy-PID
    做过模糊PID的朋友很多遇到过这种问题,就是仿真启动不起来,停留在e-7等地方或者仿真很慢,自次上次有个朋友说改变步长能解决这个问题,最后的曲线能达到满足要求的时候,我让他找个例子他就没有后文,以前我做了很多这样的模糊PID,但靠改变步长并没有解决问题,仿真曲线直接发散出去了,我自己这两天也总在思考这个问题,通过不断的调试总结,明白了不少,给遇到这个问题的朋友讲解一下解决办法吧,以一个例子详解:(Done a lot of friends of the fuzzy PID encountered this problem, simulation start up, stay in the e-7 and other local or simulation is very slow, have a friend who said to change the step size to solve this problem since the times the last, the finalcurve to achieve to meet the requirements when I asked him to find examples of his later, I have done a lot of fuzzy PID, but by changing the step does not solve the problem, the simulation curve directly divergence out, Itwo days always thinking about this problem, summarized by the debug and understand a lot of friends to experience this problem to explain the solution, an example Detailed:)
    2012-04-11 08:45:48下载
    积分:1
  • Am
    说明:  am modulation with simulink
    2012-08-09 19:30:46下载
    积分:1
  • mixiangqu
    基于MATLAB/simulink仿真平台的循环流化床锅炉燃烧系统的密相区仿真模型(Based on MATLAB/simulink simulation platform circulating fluidized bed boiler combustion system simulation model of dense phase region)
    2013-10-06 16:01:19下载
    积分:1
  • wind_load
    船舶操纵运动仿真模型之风力模型研究(根据经验公式得出)(Research ship motion simulation model of the wind model manipulation (based on empirical formulas derived))
    2014-01-10 12:27:26下载
    积分:1
  • 696516资源总数
  • 106409会员总数
  • 8今日下载