-
umat Isotropic Strain Hardening Plasticity
可以用于在ABAQUS中进行蠕变损失分析(For creep rupture analysis in ABAQUS)
- 2019-05-21 13:12:46下载
- 积分：1
-
ABAQUS_UMAT的开发
umat基础知识教学，适合刚接触UMAT的新手做参考(UMAT basic knowledge teaching, suitable for beginners)
- 2018-12-28 17:00:40下载
- 积分：1
-
wave simulation
通过频谱来模拟波浪，程序为Jonswap谱的波浪模拟，可随意调整谱参数、时间间隔和模拟的时间长度(The wave is simulated by the spectrum, and the program is a wave simulation of the Jonswap spectrum. The spectral parameters, time interval and length of the simulation can be adjusted at will.)
- 2021-01-04 15:58:55下载
- 积分：1
-
map
用于绘制电机效率等高线图的程序，横坐标的转速，纵坐标转矩(A program for drawing contour diagrams of motor efficiency,the speed of the abscissa and the torque of the ordinate.)
- 2018-09-06 18:17:01下载
- 积分：1
-
matlab接安捷伦
matlab连接安捷伦示波器，可以显示单个通道数据，自己设置采样点数，设置内存深度，可以通过改变循环达到长时间监控目的（数据传输有延时，用于捕捉信号时要延长监控时间）。(matlab Connect the agilent oscilloscope)
- 2017-09-29 16:52:07下载
- 积分：1
-
三维凸包
matlab画三维凸包，根据一些离散点，效果非常好(Matlab draws three-dimensional convex hull, according to some discrete points, the effect is very good.)
- 2021-02-26 14:09:37下载
- 积分：1
-
五轴后处理
基于hypermill 10的五轴后处理转换器，优化了算法，中文界面。支持多种结构的五轴机床刀路仿真，输出高质量刀路。是五轴雕刻机的必备后处理转换器。(Based on the hyperMILL 10 five axis post processing converter, the algorithm, the Chinese interface is optimized. Support a variety of structure of the five axis machine tool path simulation, output high quality tool path. It is the necessary post-processing converter for the five axis engraving machine.)
- 2018-01-24 20:46:28下载
- 积分：1
-
adrc
ADRC算法TD微分跟踪器simulimk框图(ADRC algorithm TD differential tracker simulimk block diagram)
- 2018-10-21 08:21:43下载
- 积分：1
-
ELM分类预测
说明： 极限学习机用于数据建模，可定性定量。代码有相关解释，直接运行。(The extreme learning machine is used for data modeling and can be qualitatively quantified.The code has an explanation and runs directly.)
- 2020-06-16 12:00:01下载
- 积分：1
-
usermat_CDM
These composite materials generally exhibit brittle damage behavior. The anisotropy in the
material and different kinds of failure mechanisms make it difficult to accurately
characterize the behavior of composite materials. The present work aims to verify and
apply the Puck Failure Criteria using the commercially available finite element package
ANSYS by writing a user-material subroutine in FORTRAN. The model is implemented
with different post failure degradation schemes EWM/CSE.
- 2019-05-01 00:48:50下载
- 积分：1
