网站首页

随机共振仿真代码

于 2020-05-08 发布

 0  360

下载积分: 1 下载次数: 10

我要下载

代码说明：

说明：基于仿真噪声信号的随机共振分析，结果准确可靠(Based on stochastic resonance analysis of simulated noise signal, the results are accurate and reliable)

文件列表：

随机共振仿真代码\duff.m, 393 , 2012-03-05
随机共振仿真代码\noise.m, 438 , 2012-03-05
随机共振仿真代码\runduffsr.m, 4679 , 2012-03-05
随机共振仿真代码, 0 , 2020-05-08

下载说明：请别用迅雷下载，失败请重下，重下不扣分！

发表评论

0 个回复

可见光通信最大化最小速率_matlab
说明：计算可见光通信中最大化最小速率的优化问题，还有稳健波束成形(The optimization problem of maximizing the minimum rate and robust beamforming are also discussed)

2020-08-11 20:08:27下载

积分：1
fmcw_positioning_radar-master
说明：基于FMCW雷达的多天线定位系统,2018年英特尔杯嵌入式邀请赛作品。(Multi antenna positioning system based on FMCW radar)

2020-06-15 22:22:30下载

积分：1
EKF_for_One_Div_UnLine_System
说明：对目标追踪的ekf算法，pf算法，ukf算法的比较，误差分析(Comparison and error analysis of EKF algorithm, PF algorithm and UKF Algorithm for target tracking)

2020-04-02 16:43:04下载

积分：1
滞环电流控制
三相永磁同步电机的滞环电流控制仿真模型，控制瞬态电流输出。(Simulation Model of hysteresis current Control for Three-phase permanent Magnet synchronous Motor)

2020-10-26 12:00:00下载

积分：1
衍射模拟
说明：用来模拟光学中各种孔径的菲涅耳衍射和夫琅禾费衍射，清晰明了(It is used to simulate Fresnel diffraction and Fraunhofer diffraction of various apertures in optics. It is clear and clear)

2020-05-02 10:15:21下载

积分：1
VSG_wuyuan_OK_2
一种虚拟同步发电机仿真模型，通过投切负荷达到频率波动的效果，然后VSG根据控制策略改变输出。(A virtual synchronous generator simulation model achieves the effect of frequency fluctuation by switching loads, and then VSG changes the output according to the control strategy.)

2021-04-21 11:08:49下载

积分：1
UMMDp180718
说明：新的屈服准则ABAQUS子程序UMAT，含有多种较新的准侧，能很好运用(The new yield criterion ABAQUS subroutine UMAT contains a variety of newer standards and can be used very well.)

2021-03-22 21:19:16下载

积分：1
chongfukongzhi
实现有源电力滤波器的电流跟踪控制，能够代替传统PI控制策略(Active power filter current tracking control can replace the traditional PI control strategy)

2017-08-28 19:27:40下载

积分：1
五轴后处理
基于hypermill 10的五轴后处理转换器，优化了算法，中文界面。支持多种结构的五轴机床刀路仿真，输出高质量刀路。是五轴雕刻机的必备后处理转换器。(Based on the hyperMILL 10 five axis post processing converter, the algorithm, the Chinese interface is optimized. Support a variety of structure of the five axis machine tool path simulation, output high quality tool path. It is the necessary post-processing converter for the five axis engraving machine.)

2018-01-24 20:46:28下载

积分：1
2dcohesive
说明：平面用cohesive单元模拟仿真裂纹扩展和结构失效，裂纹扩展(Plane simulation of crack growth and structure failure, crack growth with cohesive element)

2019-11-21 10:38:54下载

积分：1

696518资源总数
105531会员总数
4今日下载

随机共振仿真代码

0 个回复

热门标签

热门下载