网站首页

登录

上车按键后开始计价。有实时时钟、单价、距离和总价钱显示。可以通过键盘修改单价（元/公里）和时间。有清除键用以清楚上次费用。利用LCD分别显示时间、单价、路程和费...

于 2022-01-22 发布文件大小:4.73 kB

 0  172

下载积分: 2 下载次数: 1

我要下载

代码说明：

上车按键后开始计价。有实时时钟、单价、距离和总价钱显示。可以通过键盘修改单价（元/公里）和时间。有清除键用以清楚上次费用。利用LCD分别显示时间、单价、路程和费用。LED辅助显示说做操作。-Button on the bus after the valuation. Real-time clock, unit price, distance, and the total price display. You can modify the keyboard unit price (yuan/km) and time. There is the clear key to clear the last cost. Respectively, using LCD displays time, price, distance and cost. LED auxiliary display saying that operation.

下载说明：请别用迅雷下载，失败请重下，重下不扣分！

发表评论

0 个回复

TS12864A
TS12864A-3 图形点阵液晶显示模块使用手册。-TS12864A-3 graphic dot matrix LCD Module User

2023-06-26 03:20:04下载

积分：1
三
三相步进电机的三相六拍工作方式，正转的绕组通电顺序：A、AB、B、BC、C、CA、A，反转的通电顺序：A、AC、C、CB、B、BA、B、A。由于步进电机转子有一定的惯性以及所带负载的惯性，故步进电机的工作过程中不能及时的启动和停止，在启动时应慢慢的加速到预定速度，在停止前应逐渐减速到停止，否则，将产生失步现象。步进电机的控制问题可总结为两点： 1、产生工作方式需要的时序脉冲； 2、控制步进电机的速度，使它始终遵循加速、匀速、减速的规律工作。 -Three-phase three-phase stepper motor six shot work, is to order the winding power: A, AB, B, BC, C, CA, A, reverse the order of power: A, AC, C, CB, B, BA, B, A. As the stepper motor rotor has a certain degree of inertia, as well as brought about by the inertia load, the stepper motor during the course of work should not start and stop time, start to be slowly accelerated to a predetermined speed, the stop should be to slow down gradually to the stop, otherwise, will result in out-of-step phenomenon. Stepper motor control problems can be summarized in two points: one, resulting in the need to work the timing pulse 2, control the speed of stepper motor, so that it always followed acceleration, velocity, deceleration of the law of the work.

2022-07-20 15:21:46下载

积分：1
8路数字电压表,有过流保护,过载保护
8路数字电压表,有过流保护,过载保护-8-way digital voltage meter, has over-current protection, overload protection

2022-08-23 06:47:13下载

积分：1
用数码管显示测得的心率值。并控制发光二极管的亮灭。
用数码管显示测得的心率值。并控制发光二极管的亮灭。-Digital display of heart rate measured value. And control of light to eliminate light-emitting diodes.

2022-04-22 00:05:18下载

积分：1
LCD12864的串口驱动程序，在keil uvision开发平台。
lcd12864 的串行驱动程序，于keil uvision 开发平台。-lcd12864 serial driver, in keil uvision development platform.

2022-06-20 01:56:16下载

积分：1
用AT89C51实验板的两位数码管显示00～99依次循环的汇编语言程序
用AT89C51实验板的两位数码管显示00～99依次循环的汇编语言程序-AT89C51 board with two digital tube display 00 to 99 followed by the cycle of assembly language program

2022-03-26 10:35:15下载

积分：1
51单片机对 siemens4442卡的底层驱动程序把.rar改成.C即可
51单片机对 siemens4442卡的底层驱动程序把.rar改成.C即可-51 Singlechip siemens4442 card on the bottom of the driver. Rar changed. C can be

2023-01-18 09:50:03下载

积分：1
常用串行EEPROM的编程应用，EEPROM是"Electrically Erasable Programmable Read...
常用串行EEPROM的编程应用，EEPROM是"Electrically Erasable Programmable Read-only"（电可擦写可编程只读存储器）的缩写，EEPROM在正常情况下和EPROM一样，可以在掉电的情况下保存数据，所不同的是它可以在特定引脚上施加特定电压或使用特定的总线擦写命令就可以在在线的情况下方便完成数据的擦除和写入-Commonly used application of serial EEPROM programming, EEPROM is Electrically Erasable Programmable Read-only (Xinhua EPROM) acronym, EEPROM under normal circumstances and EPROM, as in the case of power-down to save data , What is different is that it can exert in a particular pin on a specific voltage or use specific bus write command can be in the case of online data to facilitate the completion of the erase and write

2022-01-23 11:15:59下载

积分：1
Microcontroller peripheral circuit design and C language programming video tutor...
单片机外围电路设计及C语言编程视频教程内容目录V2-Microcontroller peripheral circuit design and C language programming video tutorials table of contents V2

2022-03-09 17:03:52下载

积分：1
Chinese Font display in embedded system
Chinese Font display in embedded system

2023-02-14 15:15:03下载

积分：1

696516资源总数
106409会员总数
8今日下载