-
供应链管理
单片机相关资料，应该是初学者的良师益友。-SCM-related information, should be a mentor for beginners.
- 2022-03-23 02:45:58下载
- 积分：1
-
键盘扫描算法有很多中，这个程序在IAR编译器下，用C语言描述了其中一种算法...
键盘扫描算法有很多中，这个程序在IAR编译器下，用C语言描述了其中一种算法-Keyboard scan algorithm has a lot in this process in the IAR compiler, using C language to describe an algorithm which
- 2022-10-14 13:50:02下载
- 积分：1
-
这是个火车传感器的小程序，在某车厢里存放N个传感器，当某个传感器温度超过或者低于某个指定范围，系统发出警告。...
这是个火车传感器的小程序，在某车厢里存放N个传感器，当某个传感器温度超过或者低于某个指定范围，系统发出警告。-This is a small sensor train procedures, in a vehicle storage N sensors, When a sensor temperature is over or below a certain designated areas, the system issued a warning.
- 2022-07-20 17:35:48下载
- 积分：1
-
1．熟悉硬件仿真工具KD30的使用。 2．修改样本程序 SAMP1a，使无论在计数或停止计数时，按 SW3 均对计数值清零，并停止计数。 3．编制一个秒表程序,...
1．熟悉硬件仿真工具KD30的使用。 2．修改样本程序 SAMP1a，使无论在计数或停止计数时，按 SW3 均对计数值清零，并停止计数。 3．编制一个秒表程序, 测试精度为0.1秒，按 SW1键启动计数，再按一次 SW1键停止计数。任何时候按 SW3 键停止计数，并对计数值清零。 4．按 SW1键后， 以 0.1 秒为单位开始计数，再按一次 SW1 键停止计数。若按 SW1 键时间超过2秒，则计数值清零，回到初始状态。-1. Familiar with the hardware simulation tool KD30 use. 2. Revised procedures SAMP1a samples, regardless of the count or counts at the end, according to SW3 numerical terms were right, reset, and stop counting. 3. Preparation of a stopwatch procedures, testing accuracy of 0.1 seconds, according to bond SW1 start counting, according to a key SW1 stopped counting. By SW3 any time to stop counting bond and reset the count. 4. By SW1 bond, after 0.1 seconds for start counting, according to a key SW1 stopped counting. If SW1 keys by the time more than two seconds, then reset the count and return to the initial state.
- 2023-08-01 05:40:03下载
- 积分：1
-
nR24L01_EVB开发板试验接口初始化及模块读写程序
nR24L01_EVB开发板试验接口初始化及模块读写程序-nR24L01_EVB development board initialization and test interface module to read and write procedures
- 2022-08-16 04:28:30下载
- 积分：1
-
nRF2401快速开发系统相关的帮助文档。
nRF2401快速开发系统相关的帮助文档。-nRF2401 rapid development of systems related to the help document.
- 2022-02-21 19:17:21下载
- 积分：1
-
犯错
c++2
- 2022-04-23 14:17:29下载
- 积分：1
-
keilc+ proteus light parallel port design of experiments requirements: master th...
keilc + proteus
并行口设计指示灯实验
要求：掌握80C51单片机输入输出接口使用方法
学会开关量输入输出控制的接口技术及编程方法
实验题目：8个发光二极管D1~D8分别接在单片机P1.0-P1.7端口上，一个开关接在P3.0上。要求输出端口输出 “0”时，发光二极管亮。开关闭合时，开始按P1.0-P1.1-...-P1.7的顺序依次点亮LED，再按 P1.7-P1.6 -...-P1.0的顺序点亮LED，重复循环。开关断开时，立刻停止点亮指示灯。-keilc+ proteus light parallel port design of experiments requirements: master the 80C51 microcontroller input and output interfaces Society of switch to use the amount of input and output control interface technology and programming methods Experimental subjects: eight light-emitting diodes D1 ~ D8, respectively connected to the MCU P1.0-P1 .7 port on a switch connected to the P3.0 on. Requested output port output " 0" , the light-emitting diode light. Is closed, to embark on the P1.0-P1.1-...- P1.7 in the order light LED, and then P1.7-P1.6-...- P1.0 order light LED Repeat cycle. Switch off when the stop light indicator.
- 2022-11-16 18:10:03下载
- 积分：1
-
呕心沥血花了将近一个月编写的打印机程序，可用在89C51系列
呕心沥血花了将近一个月编写的打印机程序，可用在89C51系列-born to spend nearly a month to prepare the printer procedures available in 89C51 Series
- 2022-10-28 03:00:04下载
- 积分：1
-
C8051f020在CGM12864B点阵液晶模块上显示两个位图及两个汉字
C8051f020在CGM12864B点阵液晶模块上显示两个位图及两个汉字-C8051F020 in CGM12864B dot matrix LCD module display two bitmaps and two Chinese characters
- 2022-05-31 12:16:33下载
- 积分：1
